15
GB
* Depending on model and options
Operation and control elements
You are advised to clean the appliance before switching it on
for the first time (see "Cleaning").
Switching the appliance on and off
W Switching on: Press the on/off button 3 so that the
temperature display lights up or flashes.
- The lighting will light up when the door is open.
W Switching off: Press the on/off button for approx. two
seconds so that the temperature display goes out.
Setting the temperature
The appliance is pre-set for normal operation. We recom-
mend temperatures of +5°C in the refrigerator.
In the refrigerator:
W To reduce the temperature:
Press the DOWN button 2.
W To increase the temperature:
Press the UP button 2.
- While you are entering the temperature, the set tempera-
ture will flash on the display.
- When you press the temperature setting buttons for the
first time, the most recent setting (known as the "refer-
ence setting") is displayed.
- You can change the settings in increments of 1°C by
briefly pressing the buttons again. If the buttons are held
down the temperature setting will change faster.
- The system switches over automatically about 5 seconds
after the button was last pressed and displays the aver-
age cooling temperature (known as the "actual setting").
- You can change the temperatures in the refrigerator be-
tween 9°C and 4°C.
W The temperature in the BioFresh compartment is con-
trolled automatically, between 0°C and 3°C.
If you require a higher or lower temperature, e.g. for
storing fish, you can alter the temperature setting in the
BioFresh compartment. See "Additional functions" for
more information.
Temperature display
The average temperature in the refrigerator compart-
ment is displayed in normal mode.
If "F0" to "F 5" appears in the display, the appliance has a
fault. Consult the customer service department indicating
the fault number displayed, so that they can arrange for your
appliance to be serviced accurately and quickly.
Audible warning signal
The audible warning signal helps you to protect the food in
your refrigerator and save energy.
- It will sound when the door has been open for longer
than about 1 minute.
W The signal will stop when you press the audible warning
on/off button 5,
- and when you close the door.
- The audible warning on/off button only works when the
door is open. Once the door is shut, the alarm function
automatically switches to standby.
SuperCooling
The SuperCooling function switches the appliance to the
coldest chilling setting.
It is ideal if you want to chill large quantities of food, drinks or
freshly prepared cakes or meals very quickly or if you want
greater humidity, e.g. for salad leaves.
W To switch on: Press the SuperCooling button 4 briefly
so that it lights up. The refrigerator temperature will drop
to its lowest value.
NB: The SuperCooling function uses slightly more energy.
After approx. 6 hours, however, the appliance switches
back automatically to normal energy-saving operation.
Additional functions
In set-up mode you can set the child-proof lock, adjust the
brightness of the display* and set the temperature in the
BioFresh compartment slightly lower or higher.
Activating set-up mode:
W Press SuperCooling button for approx. 5 secs - the Super-
Cooling button flashes - the display shows c for child-
proof lock.
Note: the value to be altered flashes.
W Select the required function by pressing the Up/Down but-
ton:
c = child-proof lock,
h = brightness or
b = BioFresh temperature.
W Now select/acknowledge function by pressing Super-
Cooling button briefly:
• For c = child-proof lock, press the Up/Down
button to select c1 = child-proof lock on or
c0 = child-proof lock off and acknowledge with
the SuperCooling button. When the symbol 6 is
lit, the child-proof lock is activated.
• For h = brightness, press Up/Down button to
select h1= minimum to h5 = maximum bright-
ness and acknowledge with the SuperCooling
button.
• For b = BioFresh temperature, press the
Up/Down button to select from b1 = lowest
to b9 = highest setting and confirm with the Super-
Cooling button. The altered BioFresh temperature
adjusts slowly to the new value.
NB: b5 = factory setting. By decreasing the tempera-
ture, "b4" to "b1", minus temperatures can be reached
and the food in the BioFresh compartment will freeze
slightly.
Exit set-up mode:
W To exit the set-up mode, press the On/Off button; after
2 mins. the electronic system switches over automatically.
- The normal operating mode is activated again.