Filter
Top Products
The fitting aids
Fig. 20 (30)
are required for both doors.
Therefore fit the unit doors one after the other.
u
Check 8 mm-presetting. (Distance between appliance door
and lower edge of crosspiece)
u
Slide up the assembly aids
Fig. 20 (30)
to the height of the
unit door. Lower stop edge ▲of the assembly aid = upper
edge of the unit door to be fitted.
u
Unscrew the cross-
piece
Fig. 21 (31)
by undoing the lock-
nuts
Fig. 21 (32)
.
u
Attach the cross-
piece
Fig. 21 (31)
together with the
assembly aids
Fig. 21 (30)
to the
inside of the unit
door.
Fig. 21
For 600 mm-wide recess:
u
Concentrically align the crosspiece
Fig. 21 (31)
: Mark a
short centre line on the unit door and put the tip of the arrow
on the crosspiece over it.
w
Distances to the outer edge are equal at the left and right.
For particle board doors:
u
Tightly screw the crosspiece
Fig. 21 (31)
into place using at
least 6 screws
Fig. 21 (41)
.
For frame and panel doors:
u
Tightly screw the crosspiece
Fig. 21 (31)
into place using 4
screws
Fig. 21 (41)
at the edge.
u
Raise and remove the assembly aids
Fig. 21 (30)
, turn them
and slide them into the adjacent openings.
Fig. 22
u
Attach the unit door to the adjusting bolts
Fig. 22 (33)
and
loosely screw the locknuts
Fig. 22 (32)
onto the adjusting
bolts.
u
Close the door.
u
Check the gap between the door and the surrounding unit
doors.
u
To laterally align the unit door: Move the unit door in the X
direction.
u
Align unit door in height and lateral inclination: Adjust the
adjusting bolts
Fig. 22 (33)
using a screwdriver.
w
The unit door is flush and in alignment with the surrounding
unit fronts.
u
Tighten the lock nuts
Fig. 22 (32)
.
Ensure that both metal
edges are flush
(symbol //):
u
Drill pilot holes in the
door of the unit
(possibly make
preliminary hole with a
bradawl).
Fig. 23
u
Screw the appliance door to the unit door with screws
Fig. 23 (41)
passed through the mounting brackets
Fig. 23 (34)
.
Fig. 24
u
To align the unit door in depth Z: Undo top screws
Fig. 24 (36)
, bottom hexagon head screws
Fig. 24 (35)
with
ring spanner
Fig. 24 (37)
provided, then shift the door.
u
Do not allow the knobs and sealing lips
to abut - vital for proper function!
u
Allow an air gap of 2 mm between the
unit door and the body of the unit.
For large unit doors:
u
fit a 3rd pair of mounting brackets
Fig. 11 (34)
.
u
Use the holes pre-drilled in the handle area
of the appliance door for this purpose.
u
Check the fit
of the door
and adjust if
necessary.
u
Tighten all
screws.
Fig. 25
u
Tighten the locknuts
Fig. 25 (32)
using the ring spanner
Fig. 25 (37)
, while holding fast the adjusting bolts
Fig. 25 (33)
with a screwdriver.
u
Put on and engage the
upper covers
Fig. 26 (38)
.
u
Place lateral covers
Fig. 26 (39)
in position,
slide them to the limit,
then press, until you
hear them snap into
place.
u
Attach covers
Fig. 26 (40)
sideways
and then draw them
forwards with a screw-
driver so that they snap
into place.
Fig. 26
Putting into operation
9