Miele BSD9XP Dishwasher User Manual


 
27
EN
26
EN
13/
IF OPERATING ABNORMALITIES OCCUR
Problem Possible Causes What to do?
A lot of droplets on the glasses - Lack or insufficient amount of
rinsing product.
- The dose has not been distrib-
uted.
- Positioning of the items.
- Check the indicator light and
fill the tank completely.
- If the tank is not empty after
approximately 60 washings,
call a technician.
- Arrange the items to restrict
water retention as much as
possible. Leave the door ajar
for a few minutes, if possible
Droplets on plastic items, Tefal
coatings, etc.
- These items have a low calori-
fic mass.
- Arrange the items in the upper
basket.
Poorer drying on rapid
programmes
-
On rapid programmes, the drying
temperature and drying period are
reduced to cut down the duration
of the cycle as much as possible.
- Leave the door ajar for a few
minutes.
Condensation on the wall of the
inside door or the tub.
-
Condensation may form on the
walls, particularly after the
appliance has cooled down
(sound insulation increases
this occurance)
POOR DRYING RESULTS
POOR OPERATION
Problem Possible Causes What to do?
Constant filling
A lot of waste on the large filter
at the end of the cycle.
- Drain hole situated too low for
the appliance (Cf. table fault
d012).
- The filters and drain outlets are
blocked with too much
residue.
- Drain wand has fallen on the
floor.
- Remove and clean the filters
and the bottom of the drain
outlets. Remove large residue
from the plates before putting
them in the machine.
Traces of rust on stainless steel - Quality of the stainless steel ;
not dishwasher-safe (knives in
particular)
- Use “special dishwasher-safe”
cutlery.
- Check that the lid on the salt con-
tainer is closed correctly.
13/
IF OPERATING ABNORMALITIES OCCUR
POOR WASHING RESULTS...
Problem Possible Causes What to do?
White marks
(identify what type)
- Chalky film (removable with
vinegar).
- Traces of salt (items have a
salty taste).
- Check that there is salt in the
tank (light unlit = OK).
- Check the water hardness at
the tap and that the water sof-
tener is set correctly. Adjust it
to a higher level if necessary.
- Water too hard for using a “4-
in-1” detergent without the
addition of salt.
- Check that the stopper on the
salt container is closed correctly.
White marks
(identify what type)
- Glass cloudy because water
too soft (cannot be removed).
- Check the water hardness at
the tap and that the water sof-
tener is set correctly. Some
detergents in pellet form are
more aggressive to glasses
and decorations (change the
product and use a protective
product if necessary).
Coloured marks (tea, wine, cof-
fee)
- Items poorly arranged
- Detergent dose too low; ineffi-
cient detergent
- Programme temperature too
low.
- If you use a multifunction
product.
- Turn the cavities in the items
towards the jets.
- Increase the dose; try another
detergent.
- Select a more suitable programme
with a higher temperature.
- Use the “4-in-1” option
(depending on the model).
Streaks or dried droplets on
glasses
- Lack or insufficient amount of
rinsing product.
- Rinsing product out-of-date or
inefficient.
- If you use a multifunction
product.
- Check the indicator light and
fill the tank completely. Adjust
the dispensing unit to a higher
position if necessary.
- Use a recent product (a good
product dilutes easily and
foams in cold water).
- Use the “4-in-1” option with a
setting prioritizing drying
(parametering from the menu –
depending on the model).
Dried-on marks on glasses, dull-
ness.
- If you use a multifunction
product.
- Use the “4-in-1” option with a
setting prioritizing brilliance
(parametering from the menu –
depending on the model).