Nissan Pro Trash Compactor User Manual


 
Color ink cartridge (S020036):
Colors Cyan, magenta, and yellow
Print capacity* In each color, approximately 1.2 million
characters (670 sheets/color, letter, 5%
duty at 360 dpi)
Cartridge life* 2 years from production date and up to
6 months after opening the package at
77° F (25° C); based on letter size paper
Temperature
Storage: 22 to 104° F (30 to 40° C)
1 month at 104° F (40° C)
Transit: 22 to 140° F (30 to 60° C)
1 month at 104° F (40° C)
120 hours at 140° F (60° C)
Freezing:** 21.2° F (6° C)
Dimensions
2.1 inches (W) × 2.7 inches (D) × 1.7 inches (H)
(54 mm × 67.4 mm × 41.8 mm)
* The cartridge life may vary. If you often print large graphics and dense
text, you will use up ink cartridges faster than if you print pages with
less ink coverage. Cleaning the print heads more often than
necessary will also consume ink.
** The ink thaws in approximately 2 hours at 77°F (25°C).
c
Caution:
Use only genuine EPSON ink cartridges and do not refill
them. Other products may cause damage to your printer
that is not covered by EPSON’s warranties.
Do not use an ink cartridge after the expiration date on the
package.
Mechanical
Paper feed method: Friction with auto sheet feeder
Print head life: 1 billion dots per nozzle
Total print volume: 75,000 pages
Dimensions and
weight:
Stylus Pro
Width 19.0 inches (482 mm)
Depth 20.9 inches (530 mm)
Height 7.2 inches (182 mm)
Weight 16.7 lb (7.5 kg)
Stylus Pro XL
Width 22.8 inches (580 mm)
Depth 23.5 inches (597 mm)
Height 7.2 inches (182 mm)
Weight 22.1 lb (10 kg)
Electrical
Input voltage
range:
103.5 to 132 V
Rated frequency
range:
50 to 60 Hz
Input frequency
range:
49.5 to 60.5 Hz
Rated current: 0.6 A
Power
consumption:
Approx. 20 W (during self test,
LQ at 10 cpi)
Environmental
Temperature: Operation 50 to 95° F (10 to 35° C)
Storage* –4 to 140° F (20 to 60° C)
1 month at 104° F (40° C)
120 hours at 140° F (60° C)
Humidity: Operation 20 to 80% RH
Storage* 5 to 85% RH
(without condensation)
* Stored in shipping container
Safety Approvals
Safety standards: UL 1950 with D3, CSA 22.2 950 with D3
R.F.I.: FCC part 15 subpart B class B
Fonts
The printer comes with an installed set of fonts, which are
selectable with the
Font
button on the control panel.
However, the printer always uses the fonts selected through
the software program. The only time you need to select the
printer’s installed fonts is when the software program does
not allow you to select fonts.
Interface Specifications
The printer is equipped with an 8-bit parallel interface and a
serial interface.
Parallel Interface
Data format: 8-bit parallel, IEEE P1284 mode
compatible
Synchronization: STROBE pulse
Handshake timing: BUSY and ACKNLG signals
Signal level: TTL compatible
Connector: 36-pin, Centronics compatible
EPSON Stylus Pro and Pro XL
Ink Jet Printers 8/1/95 EPSON Stylus Pro and Pro XL-3