Filter
Top Products
Searching the One Touch Banks
17
1. To store the displayed frequency in the lowest available
channel in the assigned channel-storage banks, press
ENT
when you find a frequency. The channel number
flashes.
2. Press
ENT
again to store the frequency. The channel
and frequency flash twice. If you want to cancel the
operation, press
TUNE/CLEAR
instead of
ENT
.
To scan the channel-storage banks, press the one touch
bank key, then
SCAN/MAN
while
<?h;%FEb_9;
<?h;%FEb_9;<?h;%FEb_9;
<?h;%FEb_9;
,
7?h
7?h7?h
7?h
, or
>7C
>7C>7C
>7C
appears.
±
If there is no empty channel at an available bank,
XýNý#<KBB
XýNý#<KBBXýNý#<KBB
XýNý#<KBB
(where
N
NN
N
is the bank number) appears after you press
ENT
.
To store more frequencies, you must clear some channels.
See “Clearing a Stored Channel” on Page 19. To continue
searching after
XýNý#<KBB
XýNý#<KBBXýNý#<KBB
XýNý#<KBB
appears, press
TUNE/CLEAR
.
7UKPI"6WPG
You can set the scanner to search through all receivable
frequencies from a specified frequency. You can use the
scanner's delay feature while using tune.
±
1. Repeatedly press
SCAN/MAN
until
C7D
C7DC7D
C7D
appears.
2. Enter the desired channel number you want to use as a
starting point for the tune. Then press
SCAN/MAN
again.
3. Press
TUNE/CLEAR
to start tune.
#j#
#j##j#
#j#
appears.
4. Hold down
H
or
G
for about 1 second to tune up or
down.
H
or
G
appear and the scanner searches the
frequencies.
±
5. When the scanner finds an active frequency, it stops
searching and displays the frequency's number.
6. To search for another active frequency, hold down
H
or
G
for about 1 second.
Once you find interesting frequencies during the search,
you can store them in the scanner’s channel-storage banks.
Frequencies found during tune search are automatically
assigned to channel-storage banks 9 and 10.
1. To store the displayed frequency in the lowest available
channel in the assigned banks, press
ENT
. The channel
number flashes.
±
"016'"
±
"
Searching the One Touch
Banks
If you entered a frequency that is
already stored in another channel,
#ZKFB#
#ZKFB##ZKFB#
#ZKFB# (duplicate) and the lowest-
numbered channel containing the
duplicate frequency flash for about
3 seconds. If you want to store the
frequency anyway, press ENT
again. You can then delete the
frequency later. See “Clearing a
Stored Channel” on Page 19.
Using Tune
• To reverse the tuning direction
at any time, hold down
H
or
G
for about 1 second.
• To tune up or down the selected
band in small increments (5 or
12.5 kHz steps), repeatedly
press
H
or
G
.
• To pause tuning, press
H
or
G
.
To resume tuning, hold down
H
or
G
.
• To quickly move up or down
through the frequencies, hold
down
H
or
G
. The scanner
tunes through the frequencies
until you release
H
or
G
.
• If there is no empty channel,
Xý/ý'&ý#<KBB
Xý/ý'&ý#<KBBXý/ý'&ý#<KBB
Xý/ý'&ý#<KBB appears after you
press ENT. To store more
frequencies, you must clear
some channels. See “Clearing a
Stored Channel” on Page 19.
To continue tuning after
Xý/ý'&ý#
Xý/ý'&ý#Xý/ý'&ý#
Xý/ý'&ý#
<KBB
<KBB<KBB
<KBB appears, press TUNE/
CLEAR.
20-424.fm Page 17 Monday, September 9, 2002 9:44 AM