Filter
Top Products
operating _13
02 OPERATING
Recommend Temp (Freezer) : -2°F (or -19°C )Recommend Temp (Freezer) : -2°F (or -19°C )
minimum of 40 to 60 psi (276 to 414 kPa.)
If the water pressure to the reverse osmosis system is
less than 40 to 60 psi (276 to 414 kPa):
• Check to see whether the sediment fi lter in the
reverse osmosis system is blocked. Replace the
fi lter if necessary.
• Allow the storage tank on the reverse osmosis
system to refi ll after heavy usage.
•
If your refrigerator has a water fi lter, it may further
reduce the water pressure when used in conjunction
with a reverse osmosis system. Remove the water fi lter.
If you have questions about your water pressure, call
a licensed, qualifi ed plumber.
CONTROLLING THE TEMPERATURE
Basic temperature of Freezer and
Refrigerator Compartments
The basic temperature and recommended
temperatures of the Freezer and Refrigerator
Compartments are -2°F and 38°F (or -19°C and 3°C)
respectively. If the temperature of the Freezer and
Refrigerator Compartments are too high or low, adjust
the temperature manually.
Controlling the Freezer temperature
The Freezer temperature can be set between -8°F
and 8°F (or between -22°C and -14°C) to suit your
particular needs. Press the Freezer button repeatedly
until the desired temperature is shown in the
temperature display. The temperature will change by
2°F (or 1°C) with each press. See below.
Fahrenheit : -2°F
➞
-4°F
➞
-6°F
➞
-8°F
➞
8°F
➞
6°F
➞
4°F
➞
2°F
➞
0°F
➞
-2°F.
Centigrade : -19°C
➞
-20°C
➞
-21°C
➞
-22°C
➞
-14°C
➞
-15°C
➞
-16°C
➞
-17°C
➞
-18°C
➞
-19°C.
Keep in mind that foods like ice cream may melt
at 4°F (or 0°C). The temperature display will move
sequentially from -8°F to 8°F (or from -22°C to -14°C).
• The locked symbol should be lined up with the
indicator line.
5. Touch the "Alarm/hold 3 sec
for Filter Reset" button
(
(Filter Reset)(Filter Reset)
) for about 3 seconds to
reset the water fi lter. The color of
indicator (
) changes from red
to blue, green, or yellow.
6. If you turned off the water supply, turn it back on.
For a replacement water fi lter, you can visit your
local home Improvement center or contact
the Samsung Parts distributor. Be sure the
replacement water fi lter has the SAMSUNG logo on
the box and on the water fi lter.
Link : http://www.samsungparts.com
Removing any residual matter inside the
water supply line after installing the water
fi lter.
1. Turn ON the main water supply and supply water
from water supply line.
2. Run water through the dispenser until the water
runs clear (approx. 6 to 7 minutes). This will clean
the water supply system and remove air from the
lines.
3. Additional fl ushing may be
required in some households.
4. Open the Refrigerator door and
make sure there are no water
leaks coming from the water
fi lter.
Be sure to fl ush the dispenser thoroughly,
otherwise water may drip from the dispenser.
This means that there is still air in the line.
Reverse Osmosis Water Supply IMPORTANT:
The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve
of the refrigerator needs to be between 35 and 120
psi (241 and 827 kPa).
If a reverse osmosis water fi ltration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to be a
4