Filter
Top Products
Ice Service (continued)
Icemaker Water Line
Installation Requirements
You will need a shutoff valve, two
1/4" O D compression nuts, _vo
compression sleeves and enough
1/4" O+D_copper tubing toconnect
refrigerator to water source (Your
Sears Store or Catalog Sales Office
has a kit available with a saddle-
type shutoff valve and copper
tubing. Before purchasing, make
sure a saddle-type valve complies
with your local plumbing codes)
CAUTION: Do not install icemaker
tubing in areas where temperatures
fat! below freezing
1. Find a 3/8" to 1" vertical COLD
water pipe near the refrigerator
When it is necessary to connect into
a horizontal water pipe, make the
connection to the top or side, rather
than at the bottom to avoid drawing
off any sediment from the water pipe
2. Measure from INLET on rear of
refrigerator to water pipe Add 7
feet to allow for moving refrigerator
for cleaning This isthe length of
1/4" O_D_copper tubing you will
need for the job (length from water
valve to water pipe PLUS 7 feet) l
Be sure both ends of copper tubing
are cut square,
3. Turn OFF main water supply.1
Turn on nearest faucet long enough
to clear line of water
CAUTION: When using any
electrical device (such as a power
drill) to facilitate installation, be
sure the device is insulatedor wired
in a manner to prevent the hazard
of electrical shock.
4. Using a grounded drill, drill a
3/16" hole in the vertical cold
water pipe you have selected.
Typical
ways to
connect
to water
supply
Throughfloor
1obasement
cold wc_terplpe
PIPE -! r --'-'-WAsHER
CLAMP_ ._ I
<_'_.. JJS_J _INLE'T
/
VERTICAL
i COLD WATER
I _i" PiPE
5o Fastenshutoff valve to cold water
pipe with pipe clamp. Be sure inlet
end issolidly in 3/16" drilled hole
in water pipe and washer isunder
pipe clamp Tighten packing nut
Tighten pipe clamp screws carefully
and evenly so washer makes a
watertight connection, Do not
overtighten or you may crush
copper tubing, especially if soft
copper tubing is used Now you are
ready to connect the copper tubing
SHUTOFF r_
VALVE (_
PACKING
NuT /
OUTLET
VALVE
I
COMPRESSION
SLEEVE
6. Slip compression sleeve and
compression nuton copper tubing
as shown above_ insert end of
tubing intooutlet end squarely as far
as itwill go, Screw compression nut
to outlet end withadjustable
wrench, Do not overtighten Turn
ON main water supply and flushout
tubing until water is clear Turn OFF
shutoff valve on water pipe You are
now ready to connect other end of
I/4" copper tubing to water valve
on back of refrigerator
Undersinkto Throughwali Incrawl
cold water toutillty room spaceunder
pipe cold waler pipe house
I/4"TUBETO SHUTOFF
VALVE
SION
NUT
TUBING
CLAMP
REFRIGERATOR CONNECTION
7. The water valve (supplied in the
icemaker kit, if not already on your
modet) has a compression fitting
protrudinll throughthe compressor
compartment cover at the rear
ofthe refrigerator Assemble
compression nut on compression
fitting as shown above insert end
of tubing intoconnector and tighten
compression nut Be sure end of
tubing issquare in connector and
is insertedas far as it will go Do not
overtighten_ Be sure there isenough
extra tubing (coiled into three turns
of about 10" diameter) to aIlow
refrigerator to move out from wan
after installation. Secure tubing in
metal clamp at top right corner of
compressor compartment cover,
8. Turn shutoff valve ON TIGHTEN
ANY CONNECTIONS OR NUTS
THAT LEAK°
9o Copper tubing may now be
fastened to baseboard
10. Your ice cubes can only be as
fresh-tasting as the water that
produces them, That swhy itis a
good idea to purify the water with
a water filter, The water filter isan
optional part at extra cost and is
available from the Sears Service
Center Order Filter No, 978488
and install at the inletwater tube
connection
11_Water Pressure Limitations:
Not below (15 PS.L)or above
(125 PSL)ifa problem occurs,
call your Utility Company,
IMPORTANT: It may take up to 24
hours for your icemaker to begin
producing ice,
The first few batches of ice cubes
should be thrown away, so that
remaining impurities inthe water
line will be flushed out
10