Filter
Top Products
10
OVERLAY PANEL INSTALLATION
OVERLAY PANELS
If your customer has chosen an overlay design
a
pplication, make sure that the panels you are
about to install match dimensions listed in the
Overlay Panel Specifications on page 12.
IMPORTANT NOTE:
The overlay panel must fit
over the door frame.The weightofeach panel
a
ssembly cannot exceed 23 kg, 34 kg for Models
ICBBI-36R,ICBBI-36RG and ICBBI-36F.
O
verlay models are shipped without handle
hardware. The cabinetmanufacturer or designer
will need to providehandle hardware to match
the overall decorating scheme.
To install overlaypanels,firstremove the doortrim
molding.For side-by-side models and the upper
door for over-and-undermodels,insert a screw-
drivertip intothe top corner sloton thehandle
side and pop out the trimmolding.Remove the
screwsand frame. For the drawer on over-and-
under models,insert ascrewdriver tip into the slot
on eitherside of the trim moldingrunningalong
thetop of the drawer and pop out the trim
molding.Remove the screws and frame. Referto
theillustrationsbelow.
Sub-Zero allows a 6 mmspace to slide the
b
acking materialinto placeinthe frame.Ifyour
material is thicker than a 6 mm,either rout an
edge around thepanel to get a proper fitor
mount the decorative overlay panelona sheetof
6 mm thick material and insert the backing
material into the channel.
You must allow for 3 mm space between the
b
acker board and the decorative panel, so the
panel will slide easily into the door frame.
The illustrations below provide a cross section
view ofthe three panelassembly showing place-
ment of the door/drawer/grille trim and a rear
view ofthe three panelassembly with critical
dimensions, standard for all models.
Install the handle hardware beforeinserting the
panel. We recommend larger D-style pulls.The
use ofsmall, one-piece knobs is not recom-
mended. If you use screws with thick heads, you
will need to countersink thescrews into the
backer panel before sliding the assembly into
place.
Door/Drawer/
Grille Trim
2 mm
3 mm
6 mmBacker Panel
8 mm min
3
mm
Spacer Panel
Overlay Panel
Spacer Panel
Overlay Panel
6 mm
Backer
Panel
3 mm
~19
mm
Overlay panels—cross
section
Overlay panels—three panel
assembly
Door trim Over-and-under drawer trim
REAR
ADJUSTMENT
FRONT
LEVELING LEG
Rear roller baseadjustment
LEVEL THE UNIT
Once the unit is in position, extend the front
l
eveling legs down by turning the legs clockwise
and adjust the height. The rear height adjust-
ment can be made from the front of the base.
Use a 8 mm socket to adjust the rear rollers. Turn
the 8 mm hex bolt clockwisetoraise the unit or
counterclockwise to lower it.
When the unit is leveled properly, or squared off,
d
oor and/or drawer adjustments are less likely to
be necessary. Refer to the illustration below for
location of the rear roller base adjustment.
IMPORTANT NOTE:
Be sure to reference
leveling of the unit to the floor and not to
surrounding cabinetry. This couldaffect the
operation of the unit, such as door closing.
INSTALL THE KICKPLATE
To install, screw the kickplate to brackets
attached to the inside surface of each roller base.
IMPORTANT NOTE:
The kickplate must be
removed for servicing. The floor cannotinterfere
with removal. Refer to the label mounted on the
kickplate support for heightclearance.
Reinstall the grille following the instructions on
page 8.Turn power back on to the electrical
outlet.
Slide the panel intothe frame on the door. With
t
he panel in position, replace the frame end. Be
sure the panel is inserted completely into the
channel for proper fit and alignment.
To reinstall the trim moldingon side-by-side
models and the upper doorfor over-and-under
m
odels, insert the top of the trim molding into
the grooves at the top of the door and work
d
ownward, snapping the trim moldinginto the
clips on the frame.
For the drawer on over-and-under models, start
at one end and move towards the opposite end,
snapping the trim molding into the clips on the
frame.
BUILT-IN INSTALLATION INSTRUCTIONS
ACCESSORIES
Optional acces-
soriesare available
through your
Sub-Zero dealer. To
obtainlocal dealer
information,visit
our website,
subzero.com.