Filter
Top Products
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
2
TABLE OF CONTENTS
Packaging .........................................Page 2
Introduction ......................................Page 2
General Information ..........................Page 2
New York City Approval .....................Page 3
Requirements for the
Commonwealth of Massachusetts .Page 4
Safety & Warning Information ..........Page 5
Cold Climate Insulation .....................Page 6
Location ............................................Page 6
Manufactured Home Requirements ..Page 7
Vent Termination Clearances ............Page 7
Minimum Clearances to Combustibles ..Page 9
Detailed Installation Steps .................Page 10
Typical Installation Sequence ...........Page 10
Step 1. Framing .................................Page 10
Step 2. Routing Gas Line ..................Page 10
Fireplace Specifi cations .....................Page 11
Step 3. Install the Venting System ....Page 13
Vertical Termination Systems ............Page 14
Vent Section Length Chart ................Page 14
Vertical Vent Tables and Figures ........Page 17
Horizontal Termination System .........Page 19
Horizontal Vent Tables and Figures ...Page 21
Venting Using Flexible Vent Pipe .......Page 24
Step 4. Field Wiring ...........................Page 25
Step 5. Optional Blower Kit Wiring ....Page 25
Step 6. Connecting Gas Line .............Page 26
Step 7. Checking Unit Operation .......Page 27
Step 8. Installing Logs .....................Page 28
Step 9. Installing Glass Door ............Page 31
Step 10. Burner Adjustments ............Page 31
Step 11. Hood Installation .................Page 32
Finishing Requirements ....................Page 32
Installation Accessories ....................Page 33
Gas Conversion Kits ..........................Page 35
This installation manual will help you obtain
a safe, effi cient, dependable installation for
your appliance and vent system.
Please read and understand these
instructions before beginning your
installation.
The Millivolt appliances have a millivolt
gas control valve with piezo ignition system
which provides safe, effi cient operation. If any
optional accessories that will require electrical
power are to be installed, the electrical power
must be provided at the time of appliance
installation.
The Electronic appliances have an electronic
intermittent pilot ignition system which
provides safe, effi cient operation. External
electrical power is required to operate these
appliances.
INTRODUCTION
These vented gas fi replace heaters are sealed
combustion, air circulating gas fi replaces de-
signed for residential applications.
Approved Vent Components - These fi replaces
are designed, tested and listed for operation
and installation with, the following vent com-
ponents only:
• Secure Vent™ Direct Vent System Compo-
nents,
• Secure Flex™ Flexible Vent Components
manufactured by Security Chimneys Inter-
national and
• Z-FLEX™ Model GA Venting Systems listed
to UL1777 and ULCS635 manufactured by
Flexmaster Canada Limited.
These approved vent system components are
labeled for identifi cation. DO NOT use any other
manufacturer’s vent components with these
appliances. Use only the correct size venting
(4-1/2" inner & 7-1/2" outer).
These appliances comply with National Safety
Standards and are tested and listed by OMNI-
Test Laboratories, Inc. (Report No. 116-F-29-5)
to ANSI Z21.88b-2003 (in Canada, CSA-2.33b-
2003), and CAN/CGA-2.17-M91 in both USA and
Canada, as vented gas fi replace heaters.
Both millivolt and electronic versions of
these appliances are listed by OMNI-Test
Laboratories for installation in bedrooms
and Manufactured Homes.
Manufactured Homes -
See Manufactured Home Requirements on
Page 7 for additional information.
PACKAGING
The assembled vented gas fi replace heater is
packaged with:
1 - One log set located in fi rebox area.
2 - One envelope containing the literature pack-
age which consists of the homeowner's
manual, installation instructions, and war-
ranty; envelope is located in the control
compartment.
3 - One vent restrictor to be applied as shown on
Page 13; restrictor is taped to the envelope.
4 - One hood located behind the top panel.
5 - One bag of decorative volcanic stone located
in the control compartment.
6 - One bag of glowing embers located in the
control compartment.
WARNING
Improper installation, adjust-
ment, alteration, service or
maintenance can cause injury
or property damage. Refer to
this manual. For assistance or
additional information consult
a qualifi ed installer, service
agency or the gas supplier.
This appliance is only for use with the type
of gas indicated on the rating plate. This ap-
pliance is not convertible for use with other
gases, unless a certifi ed kit is used.
Cet appareil doit être utilisé uniquement
avec les types de gaz indiqués sur la plaque
signalétique. Ne pas l'utiliser avec d'autres
gaz sauf si un kit de conversion certifi é est
installé.
Misc. Codes / Standards -
Installation must conform to local codes. In the
absence of local codes, installation must comply
with the current National Fuel Gas Code, ANSI
Z223.1. (In Canada, the current CAN-1 B149
installation code).
The appliance, when installed, must be elec-
trically grounded & wired in accordance with
local codes or, in the absence of local codes,
with the National Electrical Code, ANSI / NFPA
70-latest edition, or the Canadian Electrical
Code, CSA C22.1 - latest edition.
GENERAL INFORMATION
Note: Installation and repair should be per-
formed by a qualifi ed service person. The
appliance should be inspected annually by
a qualifi ed professional service technician.
More frequent inspections and cleanings may
be required due to excessive from carpeting,
bedding material, etc.
S'assurer que le brùleur et le compartiment des
commandes sont propres. Voir les instructions
d'installation et d'utilisation qui accompagnent
l'appareil.
Provide adequate clearances around air open-
ings and adequate accessibility clearance for
service and proper operation. Never obstruct
the front openings of the appliance.
These appliances are designed to operate
on natural or propane gas only. To operate
on Propane Gas a fi eld converion is neces-
sary (see Pages 35 to 37). The use of other
fuels or combination of fuels will degrade
the performance of this system and may be
dangerous.
These fi replaces are designed as supplemen-
tal heaters. Therefore, it is advisable to have
an alternate heat source when installed in a
dwelling.
Millivolt Models - The millivolt appliances are
manually controlled and feature a spark igniter
(piezo) that allows the appliance's pilot gas to
be lit without the use of matches or batteries.
This system provides continued service in the
event of a power outage.
Millivolt models come standard with a manu-
ally-modulated gas valve; fl ame appearance and
heat output can be controlled at the gas valve.
The BTU Input for these appliances is shown
in Tables 1 & 2.