Filter
Top Products
Water
Requirements
The hot water line to the dishwasher
must provide between 15 - 120 psi water
pressure. The hot water heater should be
set to deliver 140°F water temperature
to the dishwasher for best results.
Use 3/8” O.D. copper tubing or l/2”
plastic tubing minimum inlet line.
Dishwasher inlet valve has 3/8” N.P.T.
internal pipe thread
Drain
Requfrements
The drain hose MUST
have a high drain loop,
20” minimum ABOVE
FLOOR, to prevent
backflow or water
siphoning out of
dishwasher during
operation.
NOTE: An air gap MUST BE USED in
the high drain loop if the drain hose
is connected to house plumbing lower
than 20” above the floor.
Drain hose, supplied, meets AHAM DW- 1
test standards. Cut l-1/2” hole in
cabinet wall for drain hose. Additional
drain line (a minimum of l/2” I.D. and no
longer than 20’) can be used if needed.
Now start...
with dishwasher in kitchen.
alternate water-
line locations
1
n
Rough in water line to the dish-
washer cabinet opening using one of
the routing methods shown. Cut l/2” or
larger hole in cabinet wall for water line.
2
n
Install a
shutoff valve in the
water line where it
can be easily
used.
3
n
Flush water line into a bucket to
get rid of any particles that may clog
inlet valve. Turn shutoff valve to the
“OFF” position.
Electrical Shock Hazard
Disconnect electrical power at the
service panel (fuse box or circuit
breaker box).
Failure to do so could result in serious
injury or death.
I-----r
electrical
2-l/2”
4
l
Cut a 1- l/2” maximum hole for
power supply cord or a 3/4” minimum
hole for direct wiring in the cabinet or
floor for the electrical wiring to pass
through. If this hole is cut in a wood
cabinet, sand the hole until it is smooth.
If the hole is cut in a metal cabinet, the
hole must be covered by a grommet
(Part No. 3027971, available from your
dealer or parts supplier.
Install wall receptacle on rear or side
wall of a cabinet next to dishwasher
opening as indicated by the shaded
areas shown. Plug dishwasher power
supply cord into this receptacle.
For direct wiring install a 3/4” U. L.-listed
conduit connector to connect the
flexible armored or non-metallic
sheathed, copper cable (with
grounding wire> to the fused
disconnect, circuit breaker or junction
box. Run the cable through the hole in
the cabinet opening. The cable should
extend 24” from the back wall.
ove 4 screws.
5
n
Remove the 4 screws attaching
access panel and toe panel to
dishwasher using a l/4” hex socket, nut
driver or Phillips screwdriver. Remove
access panel and toe panel.
6
n The dishwasher is shipped to be
installed in cabinet opening with a 34”
height. Measure height of cabinet
opening from the front edge of the
underside of cabinet opening to floor.
Check chart for that height opening. Put
the wheels in the required position. The
dishwasher should be installed as level
as possible from front to back.
Loosen and then turn front levelers the
number of times indicated in the chart.
Min.
cutout
Height
Wheel Number
Position Of Turns
(See
Illustration)
To Adjust
Levelers
33-710”
1 0
34-1116” 2
3
34-114” 3
6
34-7116”
4
9
For additional height:
I. Add shims under the wheels.
2. Turn front levelers (each turn adds l/16” in
height).
You may have this type drain
connector...
7
w Put spring-type drain hose clamp
over connector. Push drain hose onto
connector. Use pliers to open clamp
and slide clamp over drain hose and
connector. Check that drain hose is
secure.
If screw-type clamp is supplied instead
of spring-type clamp, use a 5/l 6” nut
driver to tighten drain hose securely to
connector.
Panel B