Filter
Top Products
6
n
Lift up and hold wood door panel
l/4” above lower door frame.
This panel
is narrower
than
access
panel.
File or sand
edges of
goi”vdorn=’
slivers.
9
n
Important: Run fingers along
bottom of retainer to check thal
retainer is lower than the lower door
frame.
I
7
bottom
edge
To change access
color panel
/ w Inset-t retainer over
lower edge of door frame while holding
wood door panel up,
Figure
4
Cut door pa
clear acces
(For models so equipped)
8
n
Snap retainer
when door is in
open position.
I I
Heavy-duty door springs must be used if
custom door panel weighs more than 4
pounds. Heavy-duty Door Springs Kit,
Part No. 43 18050, is available from your
dealer or parts supplier. Maximum door
weight is 8 pounds.
down into place.
Push down firmly
along entire length
of retainer to make sure retainer is
secure. Slide wood door panel down.
Personal Injury Hazard
Wear gloves and handle panels
carefully.
Cut metal edges may cause personal
injury or damage to other materials.
1
n
Push UP
Ill
with thumbs‘on
each end of
access panel
top trim to
Wood access panel
This panel is wider that door panel.
unsnap trim.
Remove top trim and set it aside.
2
n
Carefully
slide color
access panel
upwards and
remove. Do Not
remove spacer.
9
n
Important: Run fingers along
bottom of retainer to check that retainer
is lower that the lower door frame.
All edges routed to 7/32” thickness.
Top view
L 7132” thick
10
n
Open and close dishwasher
A II
3
n
With
desired color
facing out, bow
access panel
and insert into
access oanel
door. Door should close easily without
slamming and open with its own weight.
If door springs need adjusting, close
door and move door springs to different
holes in the dishwasher base.
1
Figure 5
1
n
Cut wood door and access panels
using specified dimensions. Make sure
wood grain direction matches cabinet
wood grain.
2
n
File or sand edges of wood panels
to avoid slivers.
Dishwasher is subject to some humidity.
Cover both sides and edges of wood
panels with moisture-resistant sealer.
frame. Slide panel down into groove
along bottom of access panel frame.
11
n
Push up with
thumbs on each end
4
n
Line up
edges of top trim
with sides of
access panel
frame. Tilt back of
of access panel top (8. ’
Lf
\
trim to unsnap trim.
Remove top trim and set it aside.
12
n
Carefully
slide color access
panel and spacer
upwards and
n
Push up at
each end of retainer
at bottom of door
panel. Then pull
trim down and slide into place. Snap
front of trim down to cover top edge of
access panel.
remove. Save color access panel and
spacer for future use.
To install
retainer toward you. Set retainer aside.
customized wood
panels in door and
access panel
Dishwasher door panel and access
panel (if model is so equipped) can be
customized to match wood cabinets. A
standard l/4” (7/32” actual thickness)
wood panel can be used as is for
customizing the door and access
panels,
A door panel thicker than 7/32”,
requires routing the top and bottom to a
7/32” thickness.
An access panel thicker than 7/32”,
requires routing all four edges to a 7/32”.
It is recommended that a cabinet-
maker cut the customized panels
because of the precise cuts required.
(See Figures 4 and 5.)
Wood door panel
Cut accurately for a snug fit between
door side frames. Note: Custom panel
fits between, Not inside frame.
13
n
Insert wood access panel into
Personal Injury Hazard
Wear gloves and handle panels
carefully.
Cut metal edges may cause personal
injury or damage to other materials.
access panel frame. Slide panel down
into groove along bottom of access
panel frame. It may be necessary to
remove top mounting screws and tilt
access panel forward to install some
wood panels.
4
n
Slide panel(s) down
to clear console. Use both
hands to bow top and
bottom edges of color door
panel(s). Remove color
panel(s) and spacer. Save
color panel(s) and spacer 1
for future use.
14
n
Line up
edges of top trim
with sides of
access panel
frame. Tilt back of
trim down and slide into place. Snap
front of trim down to cover to edge of
wood access panel.
under control
5
between, not
inside, door frame
n
Insert top of wood door panel
between sides of door frame about 3”
below console. Rotate wood door panel
down against dishwasher door. Slide top
edge of wood door panel under bottom
edge of console. Press lower portion of
wood door panel in place between
sides of door frame.
door
side -+.+
frame
Panel E