Filter
Top Products
24 25
OPERATING YOUR BREVILLE PRODUCT
NOTE
The machine will exit Advanced
Features if there is no user input for
30 seconds or the POWER button or
MENU button is pressed.
Reset Default Settings (rSEt)
Use this function to reset all programmable
values back to the default settings. The
machine has the following default settings:
1. Shot Temperature: 93˚C
2. Low Pressure Pre-infusion:
PP60, PT7 seconds
3. Milk Temperature: 65˚C
4. Auto Start: OFF (8:00am)
5. Auto Off: 1 Hour
6. Clock: 12:00am
7. 1 CUP Button Shot Duration:
20 seconds
8. 2 CUP Button Shot Duration:
30 seconds
While 'rSET' is displayed on the LCD, press
the SELECT dial to reset all settings to
factory defaults.
+
POWER
'Hrd3' will flash on screen. Machine is
now in Water Hardness mode. See
'Water Hardness (Hrd3)' to set.
Descale (dESc)
Select this feature to access the step by step
descale procedure on the LCD. Refer to page
38 for the accompanying instructions.
Water Hardness (Hrd3)
Determine water hardness with the supplied
water hardness test strip. Refer to 'Setting
Water Hardness', page 14.
Rotate SELECT dial to the required setting
from 'Hrd1' (softest water) to 'Hrd5' (hardest
water). Press SELECT dial to set. Machine
will beep once to confirm selection.
Setting water hardness will determine the
regularity of the 'CHANGE FILTER' alert
which indicates when the water filter in the
water tank needs to be replaced.
Units (SEt)
Set units to metric or imperial. Rotate
SELECT dial to the desired unit. Press
SELECT dial to set. Machine will beep once
to confirm selection.
LCD Backlight (Lcd)
Adjust the LCD brightness/contrast.
Rotate SELECT dial to the desired
brightness. Press SELECT dial to set.
Machine will beep once to confirm selection.
Spotlights (SPOt)
Adjust the brightness of the LEDS
lighting the drip tray area. Rotate SELECT
dial to the desired brightness. Press SELECT
dial to set. Machine will beep once to
confirm selection.
Steam Temperature (StEA)
Adjust the steam boiler temperature,
which in turn controls steam pressure.
Rotate SELECT dial to the desired
temperature. The default is 135˚C. Press
SELECT dial to set. Machine will beep once
to confirm selection.
OPERATING YOUR BREVILLE PRODUCT
Air Pump Delay (Air)
This function is for advanced use only.
Delay the operation of the air pump during
automatic milk texturing. Rotate SELECT
dial to the desired delay time. The default
setting is 02 seconds. Press SELECT dial
to set. The default temperature which the
air pump turns off will be displayed. Rotate
SELECT dial to the desired temperature.
Press SELECT dial to set. Machine will beep
once to confirm selection.
Sound (Snd)
Adjust the audible alerts. Rotate SELECT
dial to the desired setting. Select between off
(OFF), low (Lo) or high (Hi). Press SELECT
dial to set. Depending on the selected
setting, the machine may beep once to
confirm selection.
Fan Control (FAn)
Adjust the speed of the internal cooling
fan. Rotate SELECT dial to the desired fan
speed. Select between Silent (SILt), Standard
(StNd) or cool (CooL). Press SELECT dial
to set. Machine will beep once to confirm
selection.
Disable Clean Me! Alert (Cln)
Disables the 'CLEAN ME!' alert. Rotate
SELECT dial to on (On) or off (OFF). The
default setting is on. Press SELECT dial
to set. Machine will beep once to confirm
selection.
12h or 24h Clock (CLoC)
Display time in 12h or 24h format. Rotate
SELECT dial to the desired unit. Press
SELECT dial to set. Machine will beep
once to confirm selection.
Flow Measurement Method (VoL)
Select between volume based (FLo) or
time based (SEc) method for espresso
dose measurement. Rotate SELECT dial
to the desired method. Press SELECT
dial to set. Machine will beep once to
confirm selection.
ALERTS
MANUAL will flash on steam LCD
The machine will not reach operating
temperature (STANDBY mode) if the steam
lever is in the MANUAL position. The steam
LCD will display 'MANUAL'. Lower the
steam lever to the centre OFF position.
Steam operation is ready when the SELECT
dial illuminates.
Fill Tank
The machine will detect a low water level.
The LCD will display 'FILL TANK'.
Fill tank with cold fresh water. The machine
will not be able to make coffee or hot water
while the tank is empty.
Clean Me!
Indicates when 200 extractions have been
carried out since the last cleaning cycle.
The cleaning cycle cleans the shower
screen and back-flushes the group head. For
information on how to clean the machine,
refer to 'Cleaning Cycle', page 34.
Heating
Indicates when the machine is heating up
or if the temperature drops excessively
during use.