Filter
Top Products
Page 42
PROGRAMMING THE BREWER (cont.)
PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)
ENABLE ADS
This function allows the operator to choose whether
or not to display an advertising message. An ad can be
saved to the brewer by either writing the ad using the
programming commands, or by entering the ad into
the brewer using an AD CARD. This message will be
displayed when the brewer is not in use.
Procedure to Enable/Disable Ads:
1. Press and hold the right hidden button until the
display reads SET LANGUAGE. Press the right hid-
den button until the display reads ENABLE ADS. The
YES or NO will be flashing to indicate the current
selection.
2. Press and release the NO button to disable this
function (no ads will be displayed on the screen),
or:
3. Press and release the YES button to enable this
function (ads will be displayed on the screen).
4. When finished, press and release DONE to save
the new setting and advance to the next function
screen.
5. If
NO was selected, the display should now read
ENABLE SANITATION. To exit programming and
return to the MAIN SCREEN, press and release the
ON/OFF pad.
6. If YES was selected, the display should now read
NEW AD?. This screen allows the operator to
select between using an ad card to read in a new
ad, writing an ad, or using the ad currently stored
in the brewer’s memory (if an ad was previously
saved).
Procedure to WRITE an Ad:
NOTE: Writing and saving a new ad will erase any
previously saved ad in the brewer’s memory.
7. From the NEW AD? screen, press and release
WRITE.
8. The display should now read 2 LINES 16 CHARS
AVAILABLE, and then SCROL THRU ALPHA, NEXT
-> NEXT LETTER, and then WRITE TOP LINE?. The
ad can be up to 32 characters long, 16 per line. The
ad will be written in two steps, first the top line,
then the bottom line.
9. To write the top line of a new ad, press and release
YES. To skip the top line and only write a bottom
line, press and release NO and proceed to step
13. To exit programming and return to the MAIN
SCREEN, press and release the ON/OFF pad.
10. The display will now read
A with a flashing cursor
below it. Press and hold the SCROLL button to scroll
through the alphabet and available characters. When
the desired character is shown on the display, press
and release NEXT to move to the next character in
the top line.
11. Repeat step 10 until the top line is complete.
12.
Press and release
DONE. The display should now
read WRITE BTM LINE?.
13. To write the bottom line of the new ad, press and
release YES.
14. To skip the bottom line, press and release
NO.
a. If neither a top nor bottom line was written, the
display should now read ENABL SANITATION.
b. If only a top line was written, the ad will be
displayed followed by SAVE? Proceed to step 18.
15. The display will now read A with a flashing cursor
below it. Press and hold the SCROLL button to
scroll through the alphabet and available charac-
ters. When the desired character is shown on the
display, press and release NEXT to move to the next
character in the bottom line.
16. Repeat step 15 until the bottom line is complete.
17.
Press and release
DONE. The display will now show
the written ad, and then SAVE?
18. To cancel saving the ad, press and release
NO.
The display should now read ADVERTISEMENT
NOT SAVED! and then will return to the NEW AD
screen. To exit programming and return to the MAIN
SCREEN, press and release the ON/OFF pad.
19. To correct or edit the ad, press and release EDIT.
The display should now read WRITE TOP LINE?
Repeat steps 10 though 17.
20. To save the ad as it is shown, press and release
YES. The display should now read ADVERTISE-
MENT SETUP COMPLETE, and then ENABL SANITA-
TION. To exit programming and return to the MAIN
SCREEN, press and release the ON/OFF pad.
36748 041504