Filter
Top Products
Page 20
PROGRAMMING THE BREWER (cont.)
12. Select DONE. The display should now read WRITE
BTM LINE?.
13. To write the bottom line, select YES.
14. To skip the bottom line, select NO.
a. If neither a top nor bottom line was written, the
display should now read ENABL SANITATION.
b. If only a top line was written, the ad will be
displayed followed by SAVE? Proceed to step 18.
15. The display will now read A with a flashing cursor
below it. Scroll through the alphabet and available
characters. When the desired character is shown
on the display, select NEXT to move to the next
character in the bottom line.
16. Repeat step 15 until the bottom line is complete.
17. Select DONE. The display will now show the written
ad, and then SAVE?
18. To cancel saving the ad, select NO. The display
should now read ADVERTISEMENT NOT SAVED!
and then will return to the NEW AD screen.
19. To correct or edit the ad, select EDIT. The display
should now read WRITE TOP LINE? Repeat steps
10 though 17.
20. To save the ad as it is shown, select YES. The
display should now read ADVERTISEMENT SETUP
COMPLETE, and then ENABL SANITATION. To exit
programming and return to the MAIN SCREEN,
press ENABLE BREW ON/OFF switch.
Procedure to READ in a new Ad:
NOTE: Saving a new ad will erase any previously saved
ad in the brewer’s memory.
7. From the NEW AD? screen, select CARD.
8. The display will show INSERT AD CARD. Place
the AD CARD vertically so that the top end of the
"chip" is beneath the sensing coil (located on the
underneath side of the front display panel).
9. After a short pause, the display will read CARD
CONTAINS AD. To view the ad, press and release
SHOW. To save the ad to the brewer's memory,
select SAVE. To cancel, select QUIT.
10. After the ad is saved, the display will read AD MES-
SAGE SETUP COMPLETE, and then will advance to
ENABLE SANITATION.
PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)
* ENABLE SANITATION
This function allows the operator to enable the sanita-
tion function and set the time before a cleaning alert
will be displayed.
Procedure for enabling sanitation:
Range: 0.0 to 72.0 hrs
1. Press and hold the right hidden button until the
display reads SET LANGUAGE. Press and release
the right hidden button until the display reads EN-
ABL SANITATION. The YES or NO will be flashing
to indicate the current selection.
2. Select NO to disable this function (no sanitation
alert will be displayed on the screen), or:
3. Select YES to enable this function (a sanitation alert
will displayed on the screen).
4. When finished, select DONE to save the new setting
and advance to the next function screen.
5. If NO was selected, the display should now read
ENABLE ENERGYSAVR. To exit programming and
return to the MAIN SCREEN, press ENABLE BREW
ON/OFF switch.
6. If YES was selected, the display should now read
X.X HRS -> CLEAN. This screen allows the opera-
tor to set the amount of time from when a brew is
completed until a sanitize alert will be displayed.
Use (-) and (+) to adjust the set time. When finished,
select DONE.
NOTE: The timer will not begin until after a brew cycle
has been completed.
7. The display should now read X.X HRS UNTIL
NEXT CLEAN, and then advance to ENABLE EN-
ERGYSAVR.
8. Once the set time has expired, the display will read
PLEASE SANITIZE, and then PRESS FULL FOR 3
SEC TO CANCEL.
9. Clean and sanitize the machine.
10. When finished, press and hold the FULL batch
switch to reset the Sanitation timer. The display
should now read SANITATION COMPLETE and then
will return to the MAIN SCREEN.
41581.2 091609
Not available on ITB