Filter
Top Products
15
stop kneading. For a finer
texture, add them sooner.)
Adding liquids
All liquid should be added
through the feed tube while
the machine is running.
Add liquid in a slow, steady
stream, only as fast as dry
ingredients absorb it. If
liquid sloshes or splatters,
stop adding it but do not
turn off the machine. Wait
until ingredients in bowl
have mixed, then add
remaining liquid slowly.
Pour liquid onto dough as
it passes under feed tube
opening. Do not pour
liquid directly onto bottom
of bowl.
Follow the recipe carefully.
It is important to add
enough liquid to make the
dough soft enough to
knead. Kneading dough
that is too stiff can strain
the machine.
All liquid except that used
to activate yeast should
be cold, to minimize the
possibility of overheating
the dough. You must never
knead a yeast dough to a
temperature higher than
100°F (37°C). Doing so will
slow or even prevent the
action of the yeast.
Kneading bread dough
Do not try to use the
machine to knead dough
that is too stiff to knead
comfortably by hand. Doing
so can strain the machine.
After the dough starts to
clean the inside of the work
bowl completely and forms
a ball, process it for 60
seconds to knead it. Stop
the machine and test the
dough to be sure it’s proper-
ly kneaded. Typical bread
dough should have a soft,
pliable texture and it should
feel slightly sticky. Stretch
the dough with your hands
to test it. If it feels hard,
lumpy or uneven, continue
processing until it feels
uniformly soft and pliable.
Make sure that the blade is
firmly pressed back into
place after removing the
dough to test it.
Kneading sweet dough
Process dough for at
least 30 seconds after
all the ingredients have
been incorporated. It will
not clean the inside of the
work bowl. If necessary,
scrape the bowl and
process for 5 more sec-
onds.
Rising
Put the dough in a large,
resealable lightly floured
plastic bag. Squeeze out all
the air and seal, allowing
space for the dough to rise.
Or put the ball of dough
in a large bowl coated
with soft butter or veg-
etable oil. Roll the dough
around to coat its entire
surface. Cover it
with a damp towel or a
piece of oiled plastic wrap.
Let it rise in a warm,
draft-free place, about 80˚F
(26˚C). The rising time is
usually about 1-1/2 hours
but will vary from
45 minutes to several
hours, depending on the
type of flour and the
humidity of the air. To
test if the dough has risen
enough, stick a finger in
it. An indentation should
remain. If it doesn’t, let
the dough rise more and
test again.
When it has risen enough,
punch the dough down.
Shaping, finishing
and baking
If you shape the dough
in loaf pans, fill pans only
half full. Let rise until dough
is just slightly above the
top of the pan. If shaping
free-form loaves, let them
rise on an oiled baking
sheet until at least
doubled in bulk.
Making consecutive
batches
You can make several
batches of bread dough
in a row. The motor in
the Premier
™
7-Cup Food
Processor is extremely
efficient.
TYPICAL
BREAD DOUGH
PROBLEMS AND
SOLUTIONS
If dough blade doesn’t
incorporate ingredients:
Always start processor
before adding liquid. Add
liquid in slow, steady
stream, only as fast as dry
ingredients absorb it. If you
hear liquid sloshing, stop
adding it but do not turn off
machine. Instead, wait until
ingredients in work bowl
have mixed, then add
remaining liquid slowly. Pour
liquid onto dough as it pass-
es under feed tube; do not
pour liquid directly onto
bottom of work bowl.
Blade rises in work bowl:
Blade may not have
been pushed down as
far as possible before
processing started.
02CU13479 DLC-2007 IB 6/30/03 12:18 PM Page 16