Filter
Top Products
Grab the blade hub, and
remove the metal blade
before tilting the bowl,
using a spatula to scrape
off any food. Then carefully
lift the blade out of the
work bowl. Or insert your
finger through the hole in
the bottom of the work
bowl, gripping the blade
from the bottom, and grip
the outside of the work
bowl with your thumb. Or
hold the blade in place with
your finger or spatula while
pouring out food.
TECHNIQUES FOR
CHOPPING AND
PURÉEING WITH
THE METAL BLADE
To chop raw fruits
and vegetables:
First cut the food into
1-inch (2.5cm) pieces.
You get a more even
chop when all pieces are
about the same size.
Put no more than the
recommended amount of
food into the work bowl
(see table inside front
cover). Lock the cover in
place. Press the PULSE
button at the rate of 1
second on, 1 second off,
until the food is coarsely
chopped. For more finely
chopped results, hold
the PULSE button, letting
the machine run continu-
ously until the desired
consistency has been
reached. Check frequently
to avoid overprocessing.
Use the spatula to scrape
down the sides of the work
bowl if necessary.
To purée fruits and
cooked vegetables:
First, cut the food into
1-inch (2.5cm) pieces.
You get a smoother purée
faster when all pieces are
about equal in size.
Put no more than the
recommended amount of
food in the work bowl (see
table inside front cover).
Lock the cover in place.
PULSE to chop coarsely,
then press the ON button
and process continuously
until food is puréed.
(NOTE: Cooked potatoes
are an exception to this
procedure. They develop
a gluey texture when
processed with the
metal blade.)
When making soup, you will
want to purée vegetables
that have been cooked in
liquid. Don’t add the liquid
to the work bowl, just the
cooked vegetables; remove
vegetables with a slotted
spoon. They will purée
faster and smoother without
liquid. Then add just enough
liquid to make the purée
pourable, return to the soup
liquid and stir to combine.
To dislodge food:
Occasionally, a piece of
food may become wedged
between the blade and the
work bowl. If this happens,
unplug the machine, remove
the cover, lift the blade
out carefully and remove the
wedged piece. Empty the
bowl, reinsert the blade
and lock the cover into
place, then insert the
pusher. Press the ON button
and drop the food pieces
through the small feed tube
opening while the machine
is running. After adding a
cupful this way, add the
remaining food to the
bowl and process in the
usual manner.
To chop hard foods:
To chop hard food like
garlic and hard cheese,
assemble the unit, remove
the small pusher, press the
ON button and drop the
food through the small
feed tube while the machine
is running.
Small foods like garlic can
be dropped in whole. Large
foods like hard cheese
should be cut into 1-inch
(2.5cm) pieces. This method
of processing minces garlic,
shallots and onions. Hard
cheese and coconut will
have the same texture as if
they had been hand grated.
IMPORTANT: Never try to
process cheese that is too
hard to cut with a knife.
You may damage the
blade or the machine.
To chop parsley and
other fresh herbs:
The herbs, the work bowl
and the metal chopping
blade must all be thoroughly
clean and dry. Remove
stems from herbs. Add
leaves to bowl and process,
using the PULSE button until
chopped as fine as desired.
The more herbs you chop at
a time, the finer chop you
can obtain. If completely dry
when chopped, parsley and
other herbs will keep for at
least 4-5 days, stored in an
airtight bag in the refrigerator.
They may be frozen for
months, stored in an airtight
container or bag.
To chop peel from citrus
fruit or to chop sticky
fruit like dates or raisins:
For citrus, remove only
the peel with a vegetable
peeler, not the white pith
which is bitter tasting.
8
02CU13479 DLC-2007 IB 6/30/03 12:18 PM Page 9