Filter
Top Products
Using Your Dishwasher
Page 10 Page 23
Installation
CONTROL PANEL
3
2
1
Power button: To turn on/off the power supply.
Menu Button: Press the Menu button, you
can select or set programs, delay time,
option functions, alternative wash and
languages.
Menu Sequences:
Program selection
Delay time setting
Option functions setting
Alternative wash function selection
Language setting
OK Button: Confirm the menu selection after
pressing the button
NOTES
1. When a selected program (and any other
functions) is finished, all of the settings will be
recorded by the system. The next time you wash,
you just need press the power and Ok buttons to
start the same washing settings as the last time.
The language setting will be recorded immediately
after you press the OK button.
2. If your machine rinse aid was previously used up,
the display screen will show add rinse aid
information when you press the power button.
This will remind you to refill the rinse aid. However
you can still keep using the machine following the
same operations as above by pressing the MENU
button to go ahead.
3. When the settings are done, the display screen will
show "please close the door". The machine will
start to work after the door is closed.
MENU DESCRIPTION
1. Program Selection:
The top line displays: Programmes
The bottom line displays: program names and
washing time.
Default program is: Normal.
Press + or - button to change the programs,
programs are: Auto, Intensive, Heavy, Normal,
Glass, 60min, Rapid and Soak.
2. Delay time setting: Can delay the washing time from
1-24 hours. Press + or - button to increase or
decrease the delay time.
3. Optional functions setting: Optional functions:
Extra Dry, Express and Power wash, default setting
is off, means no optional function is selected.
Extra drying: An increased temperature during the
final rinse to increase drying performance. There is
a slight increase in the energy consumption. (This
function can only be used with programs Intensive,
Heavy, Normal, Glass and 1 Hour).
Express: This function can reduce the washing
time. Water and energy consumption are slightly
increased. (This function can only be used with
programs Intensive, Heavy, Normal and Glass).
Power Wash: This function can wash very soiled
pots and pans. The temperature of water will be
increased during the washing cycle. (This function
can only be used with programs Intensive, Heavy,
Normal, Glass and 1 Hour).
3. Alternative wash function selection: Select both
sprayers running, upper sprayer running only or
lower sprayer running only.
4. Language setting: Languages that can be selected
are - Russian->Nederlands->English->Deutsch-
>Italiano->Francais.
‘-’ Button: Move to the left. Press the
button once the menu moves to the next
item on the left.
4
2
3
1
6
4 5
‘+’ Button: Move to the left. Press the
button once the menu moves to the next
item on the right.
5
Display Screen: To display program time,
delay time, washing stages, error codes,
program names, Languages, alternative
wash, optional functions and using
information etc;
6
Cold Water Connection
How to Connect the safety supply hose
The appliance must be connected to the water mains
using new hose-sets. The old hose-sets should not be
reused.
Water pressure must be between 0.04 MPa and 1
MPa. If the pressure is below the minimum, consult
our Service Department for advice.
If the water pipes are new or have not been used for an
extended period of time, let the water run to make sure
that the water is clear. This precaution is needed to
avoid the risk of the water inlet getting blocked and
damaging the appliance.
1. Pull the safety supply hose completely out from the
storage compartment located at the rear of
dishwasher.
2. Connect the cold water supply hose to a threaded
3/4(inch) connector and make sure that it is
fastened tightly in place.
3. Turn water fully on before starting the dishwasher.
The safety supply hose consists of the double walls.
The hose's system guarantees its intervention by
blocking the flow of water in case of the supply hose
breaking and when the air space between the supply
hose itself and the outer corrugated hose is full of
water.
WARNING! In order to avoid water staying in the
inlet hose, please close the hydrant after using.
WARNING! A hose that attaches to a sink spray
can burst if it is installed on the same water line
as the dishwasher. If your sink has one, it is
recommended that the hose be disconnected
and the hole plugged.
How to disconnect the safety supply hose
1. Turn off the water.
2. Unscrew the safety supply hose from the faucet.
AquaStop Anti-Flood Protection
Your dishwasher is fitted with an AquaStop anti-
Ÿ
flood protection system. This system consists of a
solenoid safety shut off valve which in the unlikely
event of a leak, a float switch will signal the Solenoid
to cut off the water supply. Therefore avoiding any
flooding.
Do not immerse the water inlet hose or the safety
Ÿ
valve in water. There is an electrical cable for the
safety valve in the double-walled water inlet hose.
If water inlet hose or the safety valve is damaged,
Ÿ
remove the main plug immediately.
Do not enlarge or shorten the inlet hose because it
Ÿ
contains electric parts.
Quick operation guideline: