Filter
Top Products
Using Your Dishwasher
Page 9Page 24
Install the hook on the aesthetic panel and put the
Ÿ
hook into the slot of the outer door of dishwasher
(see below).
Installation
Tension adjustment of the door
The door springs are set at the factory to the
Ÿ
proper tension for the outer door. If an aesthetic
fascia panel is installed, you will have to adjust the
door spring tension. Rotate the adjusting screw to
drive the adjustor to strain or relax the steel cable
(see below).
Adjust the door spring tension until the door
Ÿ
remains horizontal and balanced in the fully-
opened position, yet rises to a close with the slight
lift of a finger.
After positioning the panel, fix it to the door using
Ÿ
the screws supplied. Remove the four short
screws and screw in the four long screws.
FORGET TO ADD A DISH?
A forgotten dish can be added at any time before the
detergent cup opens.
1. Open the door a little to stop the washing.
2. After the spray arms stop working, you can open
the door completely.
3. Load the forgotten dishes.
4. Close the door.
5. The dishwasher will start running again after 10
seconds.
WARNING! It is dangerous to open the door
when washing, because the hot water may scald
you.
AT THE END OF THE WASH CYCLE
When the working cycle has finished, the buzzer of the
dishwasher will sound for 8 seconds, then the
dishwasher will automatically go to off-mode after the
end of the programme. (If you opened the door during
the sound, you must press the on/off button to turn it
off). Then shut off the water supply and open the door
of the dishwasher. Wait for a few minutes before
unloading the dishwasher to avoid handling the dishes
and utensils while they are still hot and more
susceptible to breakage. They will also dry better.
Switch off the Dishwasher
1. The buzzer of the dishwasher will sound for 8
seconds, then automatically go to off-mode.
2. Turn off the water tap.
Open the door carefully
Hot dishes are sensitive to knocks. The dishes should
be allowed to cool down around 15 minutes before
removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a
few minutes before removing the dishes. Dishes will
be cooler and the drying will be improved.
Unloading the Dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one.
This will avoid water dripping from the upper Basket
onto the dishes in the lower one.
Remove the 4 short screws
Screw in the
4 long screws
TURNING ON THE APPLIANCE
Starting a wash cycle:
1. Draw out the lower and upper basket, load the
dishes and push them back. It is recommended to
load the lower basket first, then the upper one (see
the section entitled “Loading the Dishwasher”).
2. Pour in the detergent (see Page 17).
3. Insert the plug into the socket. The power supply is
220-240 VAC /50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water
supply is turned on to full pressure.
4. Close the door, press the ON/OFF button to switch
on the machine.
5. Press the menu Button, then press ‘-’ or ‘+’ button
to change the program as follows:
Auto->Intensive->Heavy->Normal->Glass->60
Min->Rapid->Soak;
If a program is selected, the display screen will
show. Press the OK button, Close the door, the
dishwasher will start.
CHANGE THE PROGRAM
Premise:
1. A cycle that is underway can only be modified if it
has only been running for a short time. Otherwise,
the detergent may have already been released, and
the appliance may have already drained the wash
water.
If this is the case, the detergent dispenser must be
refilled (see the section entitled "Adding Detergent
to Dishwasher").
2. Open the door, press the Menu button, then press
‘+’ or ‘-’ button, you can change the program to the
desired cycle setting (see the section entitled
“Starting a washing program" ).
NOTE: If you open the door during a wash cycle ,
the machine will pause. The program light will
stop blinking and the buzzer will sound every
minute until you close the door. After
you close the door, the machine will keep on
working after 10 seconds.