Filter
Top Products
Automatic Oven Timer
Caution: Never let food sit in the
Function Error Tone
(series of
The oven timer will automatically
oven for more than 4 hours before
very rapid beeps, l/8-second on,
start and stop your oven cooking or
cooking starts.
Room temperature
l/4-second
off.):
display will show a
self-cleaning operation for you.
is ideal for the growth of harmful
failure code. Cancel Function Error
bacteria. Be sure oven light is off
Tone by pushing the CANCEL
For automatic oven cooking:
because heat from the bulb will
button. If the Function Error Tone
sDeed
bacteria
m-owth.
starts
again
(after about 15
1. Push COOK TIME button.
2. Turn SET knob to set length of
baking time.
3.
Push BAKE button.
4. Turn SET knob to set desired
temperature.
When cook time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off.
During automatic cooking:
●
You can push the STOP TIME
button to find out when the End-of-
Cycle Tone will sound and the oven
will turn off.
. You can push the CLOCK button
to display time of day without
canceling the oven operation.
To Delay Starting an
Automatic Oven Operation
,
Note:
You can push the
STOP
second;), call for service.
TIME button to find out when the
Disconnect the range electrical
oven will turn off. Push and hold
supply to stop the tone.
the COOK TIME button to find out
If the function error occurred
when the oven will turn on.
while
you
were
rn-om-amming
the
If a delayed self-cleaning oven
operation is desired, see
page 21.
How to Change
a Program
When a function has been
entered, you can recall what has
been programmed by pushing
the corresponding function
button. The messages in the
display show you which fimction
is currently being displayed.
While the function is displayed,
you can change it with the SET
knob. You can change any
programmed function at anytime.
If a delayed cooking operation
Tones
is desired:
1. Push COOK TIME button.
End-of-Cycle Tone (3
long
beeps–
one second on, one second off):
2. Set length of baking
time with
SET knob.
3. Push STOP TIME button.
4.
Turn SET knob to time of day
when baking should be completed.
Stop time must be equal to or
greater than the cook time plus the
current time of day.
5. Push BAKE button.
6
Turn SET knob to desired
temperature.
When stop time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off.
shows that a timed oven operation
has reached SKIP TIME or that
the Minute/Second Timer has
counted down.
Attention Tone
(series of short
beeps, l/4-second on, l/4-second
off, until proper response is given):
will sound if oven has only been
partially prog
rammed. For example,
if you have selected a cook time but
no temperature, you will hear the
Attention Tone until you select a
temperature or push CANCEL.
Electr&ic
Con{rolUpush
the
-
CANCEL button and try again.
To Cancel the Tone...
If you don’t
want an audible tone when you
push a button, you can eliminate
the Key Tone by pushing and
holding the CANCEL button until
you hear a short beep (in
approximately two seconds). To
activate the tone again, push and
hold the CANCEL button once
more until you hear a short beep.
Canceling or activating the tone
should only be done when there is
no oven operation programmed.
Pushing the CANCEL button will
clear all functions except the Clock
and Minute/Second Timer.
Notification Tone
(single,
one-
second beep): indicates oven has
stabilized at selected temperature.
Key Tone
(single, l/10-second
beep): sounds when any button is
pushed.
11