Filter
Top Products
-8- H8172 Cement Mixer
Figure 1. Inventory components picture 1.
A
B
C
D
Inventory
After all the parts have been removed from the
carton, you should have:
Main Components (Figures
1 & 2) Qty
A. Lower Drum ................................................ 1
B. Motor Assembly .......................................... 1
C. Tipping Wheel ............................................ 1
D. Upper Drum ................................................ 1
E. Support Leg ................................................ 1
F. Frame ......................................................... 1
G. Axle Bracket ............................................... 1
H. Mixing Blades ............................................. 2
I. Wheels ....................................................... 2
J. Bearing Block ............................................. 1
K. Upper Bracket ............................................ 1
L. Gasket (not shown) .................................... 1
Figure 2. Inventory components picture 2.
E
F
G
H
I
J
K
Hardware Qty
Hairpin Cotter Pin (Wheels) ..............................
2
Hex Bolts M8-1.25 x 65 (Leg to Frame) ............
2
Flat Washers 8mm (Leg to Frame) ...................
2
Lock Washers 8mm (Leg to Frame) .................
2
Hex Nuts M8-1.25 (Leg to Frame) ....................
2
Hex Bolt M6-1 x 25 (Plunger Rods) ..................
1
Lock Nut M6-1 (Plunger Rods) ..........................
1
Cotter Pin (Plunger Rod) ...................................
1
Hex Bolts M8-1.25 x 65 (Bracket to Frame) .....
2
Flat Washers 8mm (Bracket to Frame) .............
2
Lock Washers 8mm (Bracket to Frame) ...........
2
Hex Nuts M8-1.25 (Bracket to Frame) ..............
2
Hex Bolts M8-1.25 x 60 (Bearing Block) ...........
1
Flat Washers 8mm (Bearing Block) ..................
1
Lock Washers 8mm (Bearing Block) .................
1
Hex Nuts M8-1.25 (Bearing Block) ....................
1
Hex Bolts M8-1.25 x 20 (Upper Bracket) ..........
2
Flat Washers 8mm (Upper Bracket) ..................
2
Lock Washers 8mm (Upper Bracket) ................
2
Hex Nuts M8-1.25 (Upper Bracket) ...................
2
Phillips Screws M10-1.5 x 20 (Blade/Lower) ....
2
Plastic Washers 10mm (Blade/Lower) ..............
2
Flat Washers 10mm (Blade/Lower) ...................
2
Lock Washers 10mm (Blade/Lower) .................
2
Hex Nuts M10-1.5 (Blade/Lower) ......................
2
Hex Bolts M8-1.25 x 20 (Drum Pieces) ...........
10
Flat Washers 8mm (Drum Pieces) ..................
10
Lock Washers 8mm (Drum Pieces) ................
10
Phillips Screws M10-1.5 x 20 (Blade/Upper) ....
2
Flat Washers 10mm (Blade/Upper) ...................
2
Lock Washers 10mm (Blade/Upper) .................
2
Hex Nuts M10-1.5 (Blade/Upper) ......................
2
Hex Bolt M8-1.25 x 65 (Motor Assembly) .........
1
Flat Washers 8mm (Motor Assembly) ...............
3
Lock Washers 8mm (Motor Assembly) .............
3
Hex Nuts M8-1.25 (Motor Assembly) ................
3
Hex Bolts M8-1.25 x 20 (Tipping Wheel) ..........
2
Flat Washers 8mm (Tipping Wheel) ..................
2
Lock Washers 8mm (Tipping Wheel) ................
2
Hex Nuts M8-1.25 (Tipping Wheel) ...................
2
If any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTICE
Some hardware/fasteners on the inventory
list may arrive pre-installed. Check mount
-
ing locations before assuming that any
items from the inventory list are missing.