Filter
Top Products
GB
5
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Installation
WARNING - THIS APPLIANCE MUST
BE EARTHED.
Mains Connection
Your cooker should have been checked to ensure
that the voltage corresponds with your supply
voltage, this is stated on the rating plate, which is
situated on the outer rear panel.
The model number and serial number are located on
the front of the cooker, as shown on the Feature's
page.
The cooker must be connected by a competent
person such as one who is a, NICEIC registered
contractor to a suitable double-pole control unit with
a minimum rating of 32A and a minimum contact
clearance of 3mm (applicable to newer properties,
older properties where a 30A double pole control unit
and a minimum contact clearance of 3mm is
acceptable).
The double pole control unit should be fitted
adjacent to the cooker, in accordance with IEE
regulations. The control unit must be within 2 metres
of but not directly above the appliance and should
be easily accessible in the event of an emergency.
The power supply cable should conform to B.S.6004
with a conductor size of 6mm2, minimum.
Access to the mains terminals is gained by
removing the rear access cover. The mains cable
must pass through the cable clamp adjacent to the
terminal block. Sufficient cable should be used to
allow the cooker to be pulled out for servicing.
Ensure that the mains cable is routed away
from any brackets affixed to the rear panel and
is not trapped to the rear wall when pushing the
cooker into position between cabinets.
Levelling
Four feet are fitted which can be adjusted up or
down to set the height (900mm - 930mm) and level
the cooker.
The feet can be simply screwed in or out to lower or
raise the cooker.
After the correct height is achieved, lock the feet
into position by tightening the locking nut using an
open ended spanner.
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION: Some soft floor coverings may get
damaged if the cooker is not moved carefully.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Ensure oven shelves are level by using a
spirit level on the rod shelves.
Siting the Cooker
The cooker is designed to fit between kitchen
cabinets spaced 600mm apart. The space either
side need only be sufficient to allow withdrawal of
the cooker for servicing and cleaning.
It can be used with cabinets one side or both as well
as in an angled corner setting. It can also be used
freestanding.
Adjacent side walls which project above hob level,
must not be nearer to the cooker than 150mm and
should be protected by heat resistant material. Any
overhanging surface or cooker hood should not be
nearer than 650mm.
Note: This appliance must NOT be fitted on a
platform.
Moving the Cooker
Before moving your cooker, switch off at the cooker
control unit, ensure that it is cool.
Open the grill door sufficiently to allow a comfortable
grip on the underside front edge of the oven roof,
avoiding any grill elements.
Radio Interference
This appliance conforms to EN 55014 regarding
suppression of radio and television interference.
Note: Take care in moving the cooker as it is
heavy. Take care to ensure that any floor
covering is not damaged.
The cooker is fitted with a safety
chain that must be attached to a
hook, secured to the wall behind the
appliance.
This appliance conforms with the followingThis appliance conforms with the following
This appliance conforms with the followingThis appliance conforms with the following
This appliance conforms with the following
European Economic Community directives:European Economic Community directives:
European Economic Community directives:European Economic Community directives:
European Economic Community directives:
- 2006/95/
EC EC
EC EC
EC of 12/12/06 (Low Voltage) and
subsequent modifications;
- 2004/108/
ECEC
ECEC
EC of 15/12/04 (Electromagnetic
Compatibility) and subsequent modifications;
- 2009/142/
ECEC
ECEC
EC of 30/11/09 (Gas) and subsequent
modifications (only for models which use gas);
- 93/68/
EECEEC
EECEEC
EEC of 22/07/93 and subsequent
modifications.
- 2002/96/
ECEC
ECEC
EC
- 1275/2008 (Stand-by/ Off Mode)