Filter
Top Products
6 7
SECTION 1 Set-Up & First Brew
Ready to Brew Your First Cup
1. LCD Control Center will indicate
“READY TO BREW.”
2. Place a cup or mug on the Drip Tray Plate.
3. Lift the Handle and the K-Cup
®
Pack Holder
will open toward you (fig. 6).
4. Select a K-Cup
®
pack.
NOTE: Do not remove the foil
lid or puncture the K-Cup
®
pack.
5. Place a K-Cup
®
pack in the
K-Cup
®
Pack Holder (fig. 7).
CAUTION: There are two sharp needles that
puncture the K-Cup
®
pack, one above the
K-Cup
®
Pack Holder and the other in the bottom
of the K-Cup
®
Pack Holder. To avoid risk of
injury, do not put your fingers in the K-Cup
®
Pack Assembly Housing.
6.
Lower the Handle to close the Lid over the
K-Cup
®
Pack Holder. (When it is closed
completely, the LCD Control Center will
indicate “READY TO BREW” and the Small
Cup, Small Mug and Large Mug Buttons will
flash for up to 60 seconds.)
NOT READY
Setting Up Your Brewer
1. Unwrap cord and plug the Brewer into
a grounded outlet. Remove all pieces of
packing tape and clear plastic sticker
from LCD Control Center.
2. Place a large mug (10 oz. minimum) on the
Drip Tray Plate.
3. Remove the Water Reservoir from Brewer
by first removing Lid from Reservoir (fig. 1),
then lifting Reservoir straight up and away
from Brewer (may be tight), (fig. 2). Rinse
with fresh water.
IMPORTANT: You cannot use your Keurig
®
Brewer until
it has been set-up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures
below freezing, allow Brewer at least two hours to
reach room temperature before brewing. A frozen
or extremely cold Brewer will not operate.
4. Fill Water Reservoir with bottled or filtered
water so that the water level is just below the
top edge of the Water Reservoir.
5. Place Water Reservoir base into the left side
of the Brewer and be sure the Water Reservoir
Lock Tabs engage with the Brewer. Replace
Lid on Water Reservoir.
6. Press the Power Button found directly
above the LCD Control Center (fig. 3).
7. The LCD Control Center will illuminate and
indicate “NOT READY.” NOTE: A K-Cup
®
pack
should not be used for this sequence
.
NOTE: If the Water Reservoir is empty or
not in place on the Brewer, the LCD Control
Center will also indicate “ADD WATER.” None
of the buttons will be activated until water
is added to the Water Reservoir and Water
Reservoir is in place.
Small
Mug
READY
TO BREW
MENU
fig.
2
Power
ADD
WATER
NOT READY
fig.
3
fig.
4
fig.
5
fig.
6
fig.
7
fig.
1
Lock Tabs
8. The Brewer will automatically fill the
internal tank with water and then the water
will be heated. This will take about 4 minutes.
During the heating period, “NOT READY”
(fig. 4) is indicated on the LCD Control
Center. Do not lift Handle during this
heating period.
Once the water is heated, “READY TO BREW”
will be indicated and the Brew Buttons will be
illuminated (fig. 5). NOTE: You may see small
amounts of water coming from the Vent and
dripping into the Water Reservoir during this
and subsequent heating — this is normal.
9.
Lift and lower the Handle. Press the Small
Mug Button to start a cleansing brew. Pour
the hot water into the sink.
10 . The one-time set-up process is now
complete and you are ready to brew!
NOTE: The Brewer may take 15 seconds
between brews and then “READY TO BREW”
will be indicated.
dtp1005-001900 ctp09 dtp1005-001900 ctp09