Filter
Top Products
1110
SECTION 2 Controls & Indicators (LCD Control Center)
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in
the LCD Control Center. NOTE: You must set the clock if you will be using the
On/Off Time programming feature.
1.
Press the Menu Button.
2. The word “OFF” will appear at the bottom
of the LCD Control Center to indicate that
the clock is not set. The programming
options will appear on the LCD Control
Center with a small arrow pointing to “SET
CLOCK” (fig. 9). “H” (Hour) and “M” (Minute)
will appear and blink.
3. Press or hold the blue Small Cup Button under
the blinking “H” until you have reached the
appropriate hour. If the hour has passed 12,
the indicator switches from “AM” to “PM.”
4. Press or hold the blue Large Mug Button under
the blinking “M” to set the minutes.
5. When you have reached the correct time, press the Menu Button five
times to scroll through the remaining programming options and exit
the programming mode.
6. The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power
is lost, follow the procedure above to reset the time as the clock will not be
visible until the time is set.
Menu
SET CLOCK
AUTO OFF
ON OFF TIME
BREW TEMP
Set
Hours
Set
Minutes
MENU
fig.
9
c. After setting the desired Auto Off time, press
the Menu Button four times to scroll through
the remaining programming options and exit
the programming mode. “AUTO OFF SET”
(fig. 11) will now be indicated to confirm that
it has been set.
d. To cancel the Auto Off feature, press the
Menu Button twice to reach the Auto Off
programming mode. Press and release the
Small Cup Button under the blinking “H”
to advance one hour at a time until “OFF”
is indicated.
3. Program your Brewer for a specific On/Off Time. NOTE: To use this
programming feature, the clock must be set to the correct time. The clock
will not be displayed unless the time is set.
a. After setting the correct time (required), press
the Menu Button three times to program the On
Time feature. The LCD Control Center will show
the programming options with a small arrow
next to “SET ON TIME” (fig. 12).
b. Press or hold the blue Small Cup Button under
the “H” to scroll through the hours to your
desired “ON TIME” hour.
c. Press or hold the blue Large Mug Button under
the “M” to scroll through the minutes to your
desired “ON TIME” minutes.
d. After setting the desired time, press the Menu Button to save the
“ON TIME” and move to the “SET OFF TIME” (fig. 13).
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule. By programming your Brewer to turn on
each morning, you will never have to wait for the Brewer to warm up to brew
a gourmet cup of coffee.
1. Leave it ON all the time. The Brewer can be left on all the time so that it is
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn
the Brewer off at any time, simply press the Power Button. (NOTE
:
Although
the clock remains on if set, you can not brew a cup of coffee, tea or hot cocoa.)
Press the Power Button again to restore power to the Brewer. You will have
to wait for the water to heat up before the Brewer is ready to brew.
2. Set the Brewer to Auto Off following a
specified period of time after the last brew.
a. Press the Menu Button twice to program the
Auto Off feature. The LCD Control Center will
display the programming options with a small
arrow next to “SET AUTO OFF” (fig. 10).
b. Press or hold the blue Small Cup Button
under the blinking “H” to advance 1 hour at
a time, up to 9 hours.
e. If you want to set an “OFF TIME,” repeat the
procedure above in steps b & c to set your
desired “OFF TIME.”
f. To complete the process, press the Menu Button
two more times to exit the programming mode.
The LCD Control Center will indicate the options
you have set.
g. The On Time and Off Time functions operate
independently from one another. To cancel
either set function, follow the steps above and
use the “H” and “M” buttons to advance to 12:00
AM. Make sure the M button is set to :00, then
change the “H” button. When you reach 12:00
AM, the Control Center will indicate “OFF” and
the function will be disabled.
EXAMPLE
:
If you chose to set the On Time at
6:15 AM and the Off Time for 10:00 PM, then the
Brewer will be “READY TO BREW” and maintain
hot water in the tank during that time so that it is
always ready for you to brew. If you wanted to
brew outside this window, simply press the Power
Button and you can brew as soon as the water is
heated and the “READY TO BREW” is indicated on
the LCD Control Center.
NOTE
:
The “AUTO OFF” Timer and the On/Off Time programming options
operate independently but can also be programmed to work together. For example,
you can set the On Time function to turn on at 7:00 AM and then set the Auto Off
Timer function to turn off the Brewer two hours after the last brew (fig. 14).
Menu
x2
CLOCK
SET AUTO OFF
ON OFF TIME
BREW TEMP
MENU
fig.
10
11
:
56
AM
READY
TO BREW
MENU
AUTO OFF SET
CLOCK
AUTO OFF
SET ON TIME
BREW TEMP
MENU
11
:
56
AM
PM
fig.
12
CLOCK
AUTO OFF
SET OFF TIME
BREW TEMP
MENU
AM
PM
fig.
13
11
:
56
AM
READY
TO BREW
MENU
AUTO OFF SET
ON TIME SET
fig.
14
fig.
11
dtp1005-001900 ctp09
dtp1005-001900 ctp09