Filter
Top Products
8 9
7. Choose the cup size of coffee, tea or hot
cocoa by pressing the button that indicates
your choice. The Small Cup choice will yield
a 5.25 oz. serving, the Small Mug choice will
yield a 7.25 oz. serving and the Large Mug
choice will yield a 9.25 oz. serving. NOTE: If
you do not push a Brew Button in 60 seconds,
the LCD Control Center will return to “READY
TO BREW” and the Brew Buttons will be
disabled to prevent accidental activation.
Re-activate the Brew Buttons by raising and
lowering the Handle completely.
8.
The LCD Control Center will indicate
“BREWING” and the cup size you selected
will illuminate. CAUTION: There is extremely
hot water in the K-Cup
®
Pack Holder during the
brew process. To avoid risk of injury, do not lift
the Handle or open the K-Cup
®
Pack Assembly
Housing during the brew process.
9.
There may be a short pause prior to coffee
being dispensed. The entire brew process
lasts for approximately 1 minute and ends
with a burst of air to remove all liquid from
the K-Cup
®
pack.
Ready to Brew Your First Cup (Continued)
10 . Lift the Handle, remove and dispose of the
used K-Cup
®
pack. CAUTION: K-Cup
®
pack
will be hot.
11 .
Enjoy your first cup of Keurig Brewed
®
gourmet coffee, tea or hot cocoa!
12 . Your Brewer may indicate “NOT READY” as it
heats water for the next brew cycle. The
“READY TO BREW” indication will return to
the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will
fill in preparation for the next brew. The pump
will make a vibrating sound. This is normal.
Stopping the Brew Process
If you need to stop brewing after the process has started, press the Power
Button to turn the Brewer off. The flow of coffee, tea or hot cocoa will stop,
the heating element will shut off, and the blue lights illuminating the brew
buttons and Water Reservoir will disappear. NOTE: You may get less coffee, tea
or hot cocoa in your cup during your next brew. We recommend that you perform
a cleansing brew after a terminated brew. Then your NEXT brew will be the
volume you have selected.
SECTION 1 Set-Up & First Brew
Adding Water
The LCD Control Center will indicate “ADD
WATER” when the water level in the Water
Reservoir is low or if the Water Reservoir has
been removed (fig. 8). The blue light in the Water
Reservoir will also blink when water needs to be
added. The Brewer will not allow you to brew when
“ADD WATER” is indicated.
The Water Reservoir can be filled in two ways.
1.
Lift off the Water Reservoir Lid and pour water
directly into the Water Reservoir while it is still
attached to the Brewer, then replace the Lid.
2. Remove the Water Reservoir from Brewer by first removing Lid from
the Water Reservoir, then lifting the Water Reservoir straight up and
away from Brewer. Fill with water. Place the Water Reservoir back on
the Brewer and replace the Lid. IMPORTANT: Do not remove the
Water Reservoir during the brewing process.
Brewing Iced Beverages
Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Try it by
placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray Assembly
can be removed to accommodate taller cups), choose your favorite K-Cup
®
pack and press your preferred cup size. Also, look for the Brew Over Ice
™
icon
on K-Cup
®
packs that are specially crafted to brew over ice! IMPORTANT: Do not
brew into a cup made of glass. Doing so may cause the glass to crack or break.
Brewing Hot Water
Your Brewer is able to produce hot water for making hot cocoa from a packet,
for use in cooking, for making soups, etc. Simply follow the instructions on
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup
®
pack.
NOTE: After brewing a hot cocoa K-Cup
®
pack, we recommend running a
cleansing brew without a K-Cup
®
pack.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge
the water from the inner tank.
1. If there is water in the Water Reservoir, remove the Lid, then lift the
Water Reservoir straight up and away from Brewer. Discard water, rinse
and refill with water. Place the Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and lower the Handle on the
Brewer without inserting a K-Cup
®
pack.
3. The LCD Control Center will indicate “READY TO BREW” and the Small
Cup, Small Mug and Large Mug Buttons will flash. Be sure to have a
large mug on the Drip Tray Plate and then press the Large Mug Button.
4. Repeat steps 2 and 3 one more time to completely purge water from
inner tank.
If you are experiencing any problems with your Brewer, please contact
Customer Service at 1.866.901.BREW (2739).
ADD
WATER
NOT READY
fig.
8
Small Cup
(5.25 oz.)
Small Mug
(7.25 oz.)
Large Mug
(9.25 oz.)
dtp1005-001900 ctp09 dtp1005-001900 ctp09