Filter
Top Products
u
Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
After installation:
u
Remove the protective film from the decorative trims and
drawer fronts.
u
Remove all transit supports.
u
Dispose of packaging material (see 4.6) .
NOTICE
Risk of damage due to condensate!
If your appliance is not a Side-by-Side (SBS) appliance:
u
do not install the appliance directly alongside a further refrig-
erator/freezer.
u
Always see to good ventilation at the installation site.
4.6 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic film!
u
Do not allow children to play with packing material.
The packaging is made of recyclable materials:
-
corrugated board/cardboard
-
EPS moulded parts
-
polythene bags and sheets
-
polypropylene straps
u
Take the packaging material to an official collecting point.
4.7 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
u
Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
WARNING
Fire and overheating hazard!
u
Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the instal-
lation site have to conform with the data on the type plate (see
Appliance at a glance).
Connect the appliance only with a properly installed
socket outlet with earthing contact. The socket outlet
must be fused with 10 A or higher.
u
Check the electrical connection.
u
Clean the appliance (see 6.3) .
u
Plug in the power plug.
4.8 Switching on the appliance
Note
u
To switch on the entire appliance it is necessary only to switch
on the freezer compartment.
Put the appliance into operation about 2 hours before first loading
food to be frozen.
Do not load food to be frozen before the temperature display
reads -18 °C.
4.8.1 Switching on the freezer compartment
u
Press On/Off button, freezer compartment
Fig. 2 (3)
.
w
The refrigerator compartment temperature display shows the
set temperature.
w
The freezer compartment temperature display and the alarm
button flash until the temperature is sufficiently cold. If the
temperature is above 0 °C, dashes flash. If it is below, the
current temperature flashes.
4.8.2 Switching on refrigerator and BioFresh
compartment
u
Press On/Off button, refrigerator compartment
Fig. 2 (11)
.
w
The interior light is on when the door is open.
w
The temperature displays shine. Refrigerator and BioFresh
compartment and freezer compartment are switched on.
5 Control
5.1 Saving energy
u
Always pay attention to good ventilation.
u
Keep the time the appliance is open to a minimum.
u
Store food logically.
u
First cool warm food to room temperature before storing it .
u
Defrost frozen food in the refrigerator.
5.2 Brightness of the temperature dis-
play
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.2.1 Adjusting the brightness
The brightness is adjustable between h1 (no illumination) and
h5 (maximum luminosity).
u
To activate the setting mode: press the SuperFrost button
Fig. 2 (2)
for about 5 s.
w
The display indicates c.
w
The SuperFrost button flashes.
u
Using the Up setting button, freezer compartment
Fig. 2 (5)
or
Down setting button, freezer compartment
Fig. 2 (4)
, select
h.
u
To confirm: briefly press the SuperFrost button
Fig. 2 (2)
.
u
To make the display brighter: press Up button,
freezer compartment
Fig. 2 (5)
.
u
To make the display darker: press Down button,
freezer compartment
Fig. 2 (4)
.
u
To confirm: press SuperFrost button
Fig. 2 (2)
.
w
The brightness is adjusted to the new value.
u
To deactivate the set-up mode: press On/Off button, freezer
compartment
Fig. 2 (3)
.
-or-
u
Wait for 5 minutes.
w
The temperature is indicated again in the temperature display.
5.3 Child proofing
The child-proofing function enables you to make sure that the
appliance is not inadvertently switched off by playing children.
5.3.1 Setting the child lock
u
To activate the setting mode: press SuperFrost button
Fig. 2 (2)
for about 5 s.
w
The display indicates c.
w
The button SuperFrost flashes.
u
Briefly press the SuperFrost button
Fig. 2 (2)
to confirm.
u
To switch on: Using the Up setting button, freezer
compartment
Fig. 2 (5)
or Down setting button,
freezer compartment
Fig. 2 (4)
, select c1.
Control
10