Filter
Top Products
16
K/SK/es..0
- Insert hinge pin 7 in the other retaining hole. Use the
hexagon socket on the open-ended spanner provided
(spanner width 5).
- Fit covers 8 again: insert hinge-side cover by sliding
outwards and click into position; insert handle-side cover
by sliding inwards and click into position.
- Bottom: Using a screwdriver, remove the spacer bo and
replace on the other side, fig. T1.
W Re-attach the door:
- Remove plugs bp from the door mounting points and
replace on the other side.
- Only on 1644 mm and 1841 mm high stainless-steel ap-
pliances: Unscrew the closure dl underneath the door on
the hinge side. Fit the closure provided separately dm on
the new hinge side and screw into place with the
same screw dn. Discard the old closure dl (or keep
it for later use).
- Suspend door with spacer in hinge pin 7, close door.
- Rotate hinge component 4 by 180°, remove hinge pin 5,
turn by 180° and replace. Mount both parts in the hinge bq:
slide the pin into the door mounting through the hinge, tilt in
the hinge component, slide up and attach with screw 3.
W Align the door flush with the body of the appliance using
the slot on the hinge bq, then tighten screw 3.
W Attach the plinth panel 1 and click into place by pressing.
W With the door open, insert the cover 2 in the plinth panel
at the front and click into place at the back.
W Transfer* door handle br and plugs bt. With the door
open, carefully lift out the pressure plates* bs at the front
and slide away; unscrew handle.
Reassemble in reverse order: replace the pressure plates
and click into position.
Dimensions
The external dimensions of the appliance can be seen on
the illustration on the opposite page (fig. S) and in the table
below.
Gross capacity External dimensions [mm]
of appliance [l] A B C D E F
(see type plate)
_____________________________________________________
258 (26..) 1250 600 631 614 644 1179
309 (31..) 1447 600 631 614 644 1179
362 (36..) 1644 600 631 614 644 1179
413 (42..) 1841 600 631 614 644 1179
_____________________________________________________
362 (36..) 1644 660 683 662 704 1287
413 (42..) 1841 660 683 662 704 1287
Installation instructions
- Do not install the appliance directly next to another refrig-
erator or freezer. This is important to prevent condensa-
tion and consequential damage resulting from it.
- This does not apply to Side-by-Side models (SBS). They
are designed for Side-by-Side installation with another
refrigerator/freezer.
The "Installation instructions for Side-by-Side combina-
tions" are supplied in the accessories bag for the SBS
freezer or the appliance with a freezer compartment.
Changing over door hinges
On appliances which are intended for individual installation
the door hinges can be changed from one side to the other.
On SBS appliances in stainless steel finish, which are de-
signed for Side-by-Side installation, the door hinges must
not be transferred to the other side!
W Only change over door hinges when mains plug is dis-
connected!
W Fig. T. With the door open, lever out plinth panel 1 on
the hinge side with a screwdriver and remove from front.
- Lever out cover 2 with a screwdriver.
Close door.
- Unscrew screw M5 3.
W Pull hinge component 4 with hinge pin 5 out from un-
derneath and remove.
W Open door, lift out at bottom and remove; do not lose the
spacer bl.
W Transfer all hinge components onto the other side:
W Top: depending on version, proceed as follows:
Version I (visible operating panel): Lever out covers 8
with a screwdriver at the front and remove at an angle
from below. Remove hinge pin 7 and insert on the op-
posite side. Use the hexagon socket on the open-ended
spanner provided (spanner width 5). Fit covers 8 again:
insert at rear and click into place at front.
Version II (concealed operating panel): Lift up cover 8
on handle side, push outwards; lift up cover on hinge side
and pull off.
- Unscrew earthing plate cm: first earthing screw cl, then
inner retaining screw cq.
- Unscrew hinge 9: first undo earthing screw cl, then re-
taining screws cq. Fit hinge 9 to opposite side: for easy
assembly, fit hinge from above and first tighten with the
upper retaining screw cq M5, then screw cq and finally
earthing screw cl M4.
- Turn earthing plate cm through 180° and screw tight again
on the new handle side: first retaining screw cq, then
earthing screw cl.
Instructions for installation and modification
* Depending on model and options