Filter
Top Products
©2004 Maytag Services 16023415 B–15
Use and Care - Model MGR6875AD*
9
Oven Cooking
To restore the Clock display:
Press and hold the Upper Oven CANCEL and Clock pads for
three seconds. The time of day will reappear in the display.
Timer
Each timer can be set from one minute (00:01) up to 99 hours
and 59 seconds (99:59).
The timers can be used independently of any other oven
activity. They can also be set while another oven function is
operating.
The Timers do not control the oven.
To set the Timer:
1. Press the Timer 1 or 2 pad.
• 00:00 and TIMER 1 or TIMER 2 flash in the display.
2. Press the appropriate number pads until the correct time
appears in the display.
• TIMER 1 or TIMER 2 will be displayed. If both times are
active, TIMER 1 and TIMER 2 will be displayed.
• The colon and TIMER 1 or TIMER 2 will continue to flash.
3. Press Timer pad again or wait four seconds.
• The colon stops flashing and the time begins counting
down.
• The last minute of the timer countdown will be displayed
in seconds.
4. At the end of the set time, one long beep will sound and
“End” will be displayed.
5. Press the Timer pad to clear the display.
To cancel the Timer:
1. Press and hold the corresponding Timer pad
for three seconds.
OR
2. Press the Timer pad and press ‘0’ using the number pads.
Locking the Control
and Oven Doors
The touchpad and oven doors can be locked for safety,
cleaning, or to prevent unwanted use. The touchpads will not
function when locked.
If the oven is currently in use, the touchpads and door cannot
be locked.
The current time of day will remain in the display when the
touchpads and doors are locked.
To lock both doors:
1. Press and release CANCEL pad.
2. Press and hold the Upper Oven CANCEL and
Cook & Hold pads for three seconds.
• OFF appears in the display
• LOCK flashes while the doors are locking.
Both oven doors lock. LOCK remains in the display.
To unlock both doors:
Press and hold the Upper Oven CANCEL and Cook & Hold
pads for three seconds. OFF disappears from the display and
LOCK flashes while the doors are unlocking.
0
Adjusting Sound Level
The factory default setting for sound is medium (MEd), but it
can be changed to low (LO) or high (HI). To change the
setting:
1. Press and hold Delay and upper oven CANCEL pads for
three seconds. A beep will sound. “bEEP” and the current
sound level (“LO”, “MEd” or “HI”) will appear in the
display.
2. Press the Autoset pad to increase or decrease the sound
level.
3. Wait four seconds and the new setting will be accepted.
4. If the Autoset pad is not pressed within 30 seconds, the
control will return to the existing setting.
Changing Temp °F/°C
The factory default setting for temperature is Fahrenheit. To
change the setting:
1. Press and hold the upper oven Bake and CANCEL pads for
3 seconds. A beep will sound and the current setting (°F
or °C) will appear in the display.
2. Press the Autoset pad to change the setting between °F
and °C.
3. Wait 4 seconds and the new setting will be accepted.
4. If the Autoset pad is not pressed within 30 seconds, the
control will return to the existing setting.
Note: The touchpads and oven doors cannot be locked if
the oven temperature is 400° F or above.
Fault Codes
BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK flash in the
display, press CANCEL pad. If BAKE or LOCK continue to
flash, disconnect power to the appliance. Wait a few
minutes, and then reconnect power. If the flashing still
continues, disconnect power to the appliance and call an
authorized servicer.