Filter
Top Products
89
PROGRAMMING THE MACHINE
90
PROGRAMMING THE MACHINE
Cup heating plate connection
Royal Professional is equipped with a useful cup
heating plate which can be disconnected, if
required.
Press keys
to move the asterisk to item
“CUP HEATER”. Press ENT to activate this
function.
The following message will be displayed:
"CUP HEATER "
"ON "
The keys
allow you to change the set
options “ON” or “OFF”.
Temperature selection
With Royal Professional a precise adjustment of
the coffee temperature can be executed. Move
the asterisk at the end of the line to the menu items
“Temp. l. coffee”, “Temp. coffee” or
“Temp. s. coffee” and select it by means of
the ENT key.
Depending on the selection, the following
messages will be displayed:
"TEMP. L. COFFEE "
"MEDIUM "
"TEMP. COFFEE "
"MEDIUM "
"TEMP. S. COFFEE "
The keys
allow you to change the set options
“Minimum”, “low”, “medium”, “high” or
“maximum”.
Pre-brewing function
As soon as the coffee has been moistened, the
pump stops for a while in order to allow a better
utilization of the coffee powder.
Move the asterisk at the end of the line to the
menu item “PREBREWING” and select it by
means of the ENT key.
The following message will be displayed:
"PREBREWING "
"ON "
The keys
allow you to change the set
options “ON”, “OFF”,“LONG” (in the latter
case the pump stop is longer).
Pregrinding function
By activating this function, grinding occurs every
time the doser is empty. So a ground coffee
portion is always ready in the doser, allowing a
time saving whenever the machine is often used.
This function is not recommended in all other
cases, because fresh ground coffee is by far
better.
Press keys
to move the asterisk to item
“PREGRINDING”. Press ENT to activate this
function.
The following message is displayed:
"PREGRINDING "
"ON "
The keys
allow you to change the set
options “ON”, “OFF”.
Hot water programming
Whenever this function is enabled, the selected
water amount is constantly dispensed. On the
contrary, whenever this function is disabled hot
water is dispensed until the user stops the
dispensing. Hot water amount can only
be programmed with programming
mode enabled.
- “PROG. H. WATER”. Press ENT to activate
this function.
The following message will be displayed:
"PROG. H. WATER "
"ON "
The keys
allow you to change the set
options: “ON”, “OFF”.
Cappuccino programming
Whenever this function is enabled, the same
amount of cappuccino is constantly dispensed.
On the contrary, whenever this function is disabled,
cappuccino is brewed until the user stops the
dispensing. Cappuccino amount can only
be programmed with programming
mode enabled.
Press keys
to move the asterisk to item
“PROG.CAPUC.”. Press ENT to activate this
function:
The following message will be displayed:
"PROG. CAPUC. "
"ON "
The keys
allow you to change the set
options: “ON”, “OFF”.
Coffee counter
Press keys
to move the asterisk to item
“TOTAL COFFEE” and select it by means of the
ENT key. The following message will be
displayed:
"TOTAL COFFEE "
" 1234... "
This value cannot be modified. Quit the menu by
means of the ENT or ESC keys.
Descaling
Move the asterisk at the end of the line to menu
item “Descaling” and select it by means of the
ENT key.
The following message will be displayed:
"DESCALING "
For descaling procedure, see page 85.
Timer
The timer enables the automatic switching off of
the machine after a preset period, which can be
set from 15 minutes to 12 hours after last
dispensing. If after a few seconds coffee is
brewed again, the timer is reset. If the value set
is 0:00, the timer function is not activated and
the machine does not switch off.
Move the asterisk at the end of the line to menu
item “Timer” by means of the keys
.
Press ENT to select this item.
The following message will be displayed:
"STANDBY "
"AFTER 0:00"
By means of the same keys
, select the
suitable time and confirm the value through ENT
button.
When the selected time is over the following
message is displayed:
"ENERGY "
"SAVING "
The machine stops and can be switched on
again by means of button
“standby”.
Vending functions
Royal Professional is equipped with a counter
allowing the machine statistic analysis while
detecting the different dispensing operations. It is
also equipped with another counter which is
able to stop the dispensing operations after a
certain number. These functions are protected by
a special access code.
courtesy of