Filter
Top Products
7
EFORE OPERATION
B
* Before operating your new oven, make sure you read and
understand this operation manual completely.
1) Plug in the oven.
* The digital display will show “ . “
2) Control panels can only be operated when the door is closed.
3) Oven light will go on for 1 minute whenever the door is opened
or after cooking.
4) Your oven has 3 ways to select memory numbers. See Custom
Setting 1 on page 11 to set Input Method. The factory setting
is Dual Digit Input .
Cancellation:
1. Cooking data is canceled when keys are not pressed for more
than three minutes when setting programming.
2. Cooking stops when the STOP/CLEAR pad is pressed and
cooking data remains. However if subsequent keys are not
pressed within three minutes, cooking data will be canceled.
To resume cooking press the START pad.
3. Cooking stops when the door is opened and cooking data
remains. However once the door is closed, cooking data
will be canceled if subsequent keys are not pressed within 3
minutes. To resume cooking press the START pad.
4. Cooking is immediately canceled by pressing the STOP/CLEAR
pad twice.
Checking food:
Press the STOP/CLEAR pad then open the door, check food, close
the door and press the START pad to continue cooking.
Cooking Completion:
When food is not taken out after cooking completion, End will
be shown in the display until the food is taken out.
HELPFUL TIPS for the Memory Input Method
The Memory Input Method determines how to input memory numbers for Memory Cooking and Custom Setting and Saving
memories, therefore follow the method below. Refer to HELPFUL TIPS below as well as in Memory cooking.
1. Dual Digit Input: Must input two numbers to select a
memory, even though the fi rst number is 0. Memory
programming is limited to 0 - 99.
2. Single Digit Input: Can only input one number to select a
memory. Memory programming is limited to 0 - 9.
3. Repeat Digit Input: Input one, two, or three numbers to
select a memory. Memory programming is limited to
0 - 29.
4. For Repeat Digit Input/Auto Start ON only, push number
pads within one second of the previous number.
5. Regardless of Input Method selected, Counter Check/Clear (Custom Setting 7) and Multiplication Factor for Double/ Triple Quantity
(Custom Setting 10) only use the Dual Digit Input Method. As for Custom Setting 10, enter memory number after pressing the
DOUBLE/TRIPLE QUANTITY pad.
0 2 12 22
0, 0 0, 2 1, 2 2, 2
0 2
0 2 2, 2 2, 2, 2
Memory No.
Dual Digit Input
Single Digit Input
Repeat Digit Input
Input Method
Memory
Examples
The Memory Input Method
OW TO OPERATE THE OVEN
H
Memory Cooking
* Your oven has 100 memory banks from 0 to 99. Memory
contents from memory number 0 to 29 are same in Dual and
Repeat Digit Input methods.
* Memory 0 - 9 are programmed as factory settings. See the table
of Programmed Memories and the Memory Input Method on
the right side. Memory 10 - 99 must be programmed before
using Memory Cooking. When a memory number which has
not been programmed is entered, End will be shown in the
display. See Saving Memories page 17 - 21 to programme a
new memory.
MEMORY OPERATION
Programmed Memories and the Memory Input Method
Memory
No.
Dual
Digit
Input
Single
Digit
Input
Repeat
Digit
Input
Cook
time
Output
power
1 01 1 1 5 sec. 100%
2 02 2 2 10 sec. 100%
3 03 3 3 20 sec.
100%
4 04 4 4 30 sec.
100%
5 05 5 5 40 sec.
100%
6 06 6 6 50 sec.
100%
7 07 7 7 1 min.
100%
8088 8
1 min. 15 sec.
100%
9099 9
1 min. 30 sec.
100%
0 00 0 0 2 min.
100%
R-1900M [EN].indd Sec1:7R-1900M [EN].indd Sec1:7 7/4/09 9:50:00 AM7/4/09 9:50:00 AM