Filter
Top Products
5
O
F
F
O
N
I
I
,
I
H
I
G
H
I
I
I
L
O
W
Variable Speed Model
ON/OFF switch. Up for ON; down for OFF.
HIGH/VARIABLE switch. HIGH overrides the
VARIABLE SPEED dial and is the fastest speed
available. VARIABLE speed is required to use
the VARIABLE SPEED dial.
VARIABLE SPEED dial. Allows user to select
continuously variable motor speeds ranging
from 1,000 rpm to 24,000 rpm. Active only
when HIGH/VARIABLE switch is set on
VARIABLE position.
Two-Speed Model
ON/OFF switch. Up for ON. Down for OFF.
HIGH/LOW switch. Up for HIGH. Down for LOW.
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and
clean in the groove around the water-shielded switches. You may also lightly spray
the surface around the switches with an all purpose cleaner such as Cinch
®
or 409
®
and work the switches back and forth a few times to loosen any dried residue under
switch. Leaving switches sticky will damage or burn out the switches.
H
I
G
H
V
A
R
I
A
B
L
E
1
2
3
4
5
6
7
8
9
10
I
I
I
I
I
,
I
O
FF
O
N
4
NOTE: Blenders come with several different control options. Please be sure you are
following the instructions for your blender model.
Two-Step Timer Model
ON/OFF switch. Up for ON. Down for OFF.
All times are total times. During operation, you
may interrupt timer by pressing START/STOP
switch.
TIMER DIAL. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated
only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
START TIMER switch. This is a lighted switch.
When light is lit power is on. Depress START
TIMER switch to activate timer setting and again
to stop midcycle.
20 or 45 Second Timer
Model
ON/OFF switch. Up for ON. Down for OFF.
All times are at HIGH speed. During operation,
you may interrupt timer by turning power
switch OFF.
TIMER dial. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
START TIMER switch. This is a lighted switch.
When light is lit power is on. Depress START
TIMER switch to activate timer setting.
Note on Two-Step Timers: Stop mid
cycle with START/STOP switch, not
the power switch. If the power switch
was used, wait 30 seconds for power
to recycle and the timer to reset
before resuming operation.
O
N
O
F
F
S
T
A
R
T
/
S
T
O
P
T
I
M
E
R
:
1
0
:
1
5
:
2
0
:
2
5
:
3
0
S
T
A
R
T
T
I
M
E
R
O
N
O
F
F
Bar Boss Timer Model
ON/OFF switch. Located on the front of the
machine below the switch panel, controls the
power to the machine. With the machine plugged
in, switch the machine to ON to ready the
machine for blending. Shut OFF power switch
at night or whenever the machine will be left
unattended.
START TIMER switch. This is a lighted switch.
When light is lit power is on. Depress START
TIMER switch to activate timer setting and again
to stop midcycle.
During operation, you may interrupt timer by
pressing START/STOP switch.
TIMER DIAL. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated
only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
PULSE switch. Pulse button can only be used
when the power switch is ON. The PULSE
switch can be used to quickly refresh product
in the container by depressing the switch and
holding down as long as needed.
Note on Bar Boss Timers: Stop mid
cycle with START/STOP switch, not
the ON/OFF switch. If the ON/OFF
switch was used, wait 30 seconds for
power to recycle and the timer to
reset before resuming operation.