Filter
Top Products
8
Lighting the burnersLighting the burners
Lighting the burnersLighting the burners
Lighting the burners
For easier lighting, proceed beforeFor easier lighting, proceed before
For easier lighting, proceed beforeFor easier lighting, proceed before
For easier lighting, proceed before
putting a pan on the pan support.putting a pan on the pan support.
putting a pan on the pan support.putting a pan on the pan support.
putting a pan on the pan support.
To light a burner:
z turn the relevant knob anti-clockwise to
maximum position (
), then push it down
to ignite the burner.
z After lighting the flame, keep the knob
pushed down for about
5 seconds5 seconds
5 seconds5 seconds
5 seconds. This
will allow the "thermocouple" (Fig. - lett. D)
to be heated and the safety device to be
switched off, otherwise the gas supply would
be interrupted. Then, check the flame is
regular and adjust it as required.
z To put the flame out, turn the knob to the
symbol
z.
Operation
)
AA
AA
A - Burner cap
BB
BB
B - Burner crown
CC
CC
C - Ignition electrode
DD
DD
D - Thermocouple
Do not keep the control knob pressed for more than 15 seconds.Do not keep the control knob pressed for more than 15 seconds.
Do not keep the control knob pressed for more than 15 seconds.Do not keep the control knob pressed for more than 15 seconds.
Do not keep the control knob pressed for more than 15 seconds.
If the burner does not light even after 15 seconds, release theIf the burner does not light even after 15 seconds, release the
If the burner does not light even after 15 seconds, release theIf the burner does not light even after 15 seconds, release the
If the burner does not light even after 15 seconds, release the
control knob, turn it the “off” position and wait for at least onecontrol knob, turn it the “off” position and wait for at least one
control knob, turn it the “off” position and wait for at least onecontrol knob, turn it the “off” position and wait for at least one
control knob, turn it the “off” position and wait for at least one
minute before trying to light the burner again.minute before trying to light the burner again.
minute before trying to light the burner again.minute before trying to light the burner again.
minute before trying to light the burner again.
If the burner accidentally goes out, turn the control knob to theIf the burner accidentally goes out, turn the control knob to the
If the burner accidentally goes out, turn the control knob to theIf the burner accidentally goes out, turn the control knob to the
If the burner accidentally goes out, turn the control knob to the
“off” position and wait for at least 1 minute before trying to light“off” position and wait for at least 1 minute before trying to light
“off” position and wait for at least 1 minute before trying to light“off” position and wait for at least 1 minute before trying to light
“off” position and wait for at least 1 minute before trying to light
the burner again.the burner again.
the burner again.the burner again.
the burner again.
When switching on the mains, after installation or a power cut, it is quite
normal for the spark generator to be activated automatically.
In the absence of electricityIn the absence of electricity
In the absence of electricityIn the absence of electricity
In the absence of electricity, ignition can occur without the electrical
device; in this case, approach the burner with a flame, push the relevant
knob down and turn it anti-clockwise until it reaches the maximum position.
If the control knobs become difficult to turn, please contact your local
Service Force Centre.
If the burner does not ignite, turn the control knob to zero, and try again.
If you cannot light the flame even after several attempts, check the "cap"
(Fig. - lett.
AA
AA
A) and the"crown" (Fig. - lett.
BB
BB
B) are in the correct position.