Filter
Top Products
20
Press Start / Pause / Cancel button first to switch your
machine into pause mode if you want to make any
changes in the program or function while the Delay
function is on. You will observe that the countdown
is paused. Select programs and/or add functions you
desire. Resume the delay phase and the countdown
from the point they were paused, by pressing Start
/ Pause / Cancel button.
Press Start / Pause / Cancel button for three seconds
if you want to make any cancellation while the
machine is in Delay mode. Release the button when
the Start / Pause / Cancel light and the
display
on the program display start flashing. The machine
will process the necessary operations required for
cancellation for a couple of minutes. The delay is
cancelled when the Start / Pause / Cancel indicator
light goes off and "End"
(10 d)
lights on the program
follow-up display. You may select and operate a new
program after cancellation process is over.
Press Start / Pause / Cancel button first to switch your
machine into pause mode if you want to adjust a
new time setting for the delay while the Delay function
is on. Set the desired time by pressing (+) or (-)
buttons. Start the delay countdown for the new time
you have fixed by pressing Start / Pause / Cancel
button again.
Press programe selection and half load buttons at the
same time for three seconds to activate the child lock.
Child lock indicator appears on the screen. Repeat the
same step to deactivate the child lock. Child lock does
not lock the door of the machine; rather it prevents
changing the selected program or functions and
deactivates Start / Pause / Cancel button.
Child Lock
Please check the salt indicator
(17)
on the display to
see whether there is enough softening salt in your
machine or not. You must refill the salt container
when the salt indicator comes on. If the water
hardness level is stored as (r1), salt indicator will
never come on even if the salt container is empty.
(Adjusting the water hardness level is explained
in Softening the Water section.)
Salt Indicator
Rinse Aid Indicator
Please check the rinse aid indicator
(15)
on the display
to see whether there is enough rinse aid in your
machine or not. You must refill the rinse aid container
when the rinse aid indicator comes on.
If the Rinse Aid Indicator is set to (OFF), rinse
aid indicator will never come on even if the rinse
aid container is empty.
Rinse Aid Indicator Setting
· When your machine is switched off, press Half Load
button
(2)
and then On / Off button
(8)
to switch
it on.
· Hold Half Load button
(2)
pressed and release
On / Off button
(8)
.
· Keep Half Load button
(2)
pressed for three
seconds.Rinse Aid Indicator
(15)
comes on and the
stored rinse aid indicator status of your machine
appears on the display in the format of "ON" or
"OFF".
· You can change the status of the indicator as "ON"
or "OFF" with Start / Pause / Cancel button
(1)
. If
you switch off the machine with "On/Off" button
when the status is "ON", then the rinse aid indicator
will come on when the rinse aid level in your machine
becomes low while the machine is in use. If you
switch off the machine with "On/Off" button when
the status is "OFF", then the rinse aid indicator will
never come on.
Cancelling a Programme
Press Start / Pause / Cancel button for three seconds
to cancel a program while it is operating. Release the
button when the Start / Pause / Cancel indicator
lights, at the right of the Start / Pause / Cancel button
and the program display start flashing. The machine
will process the necessary operations required for
cancellation for a couple of minutes. The program is
cancelled when the Start / Pause / Cancel indicator
light goes off and "End"
(10 d)
lights on the program
follow-up display. You may select and operate a new
program after program cancellation process is over.
There might be residues of detergent or rinse agent
left in the machine and/on the pieces being washed
depending on the step the previous program was in
at the time of cancellation.
Changing the Programme
Press Start / Pause / Cancel button first to switch your
machine into pause mode if you want to change your
selection after you started the program. Then, come
to the program you like by pressing Program Selection
button. Start the new program by pressing Start /
Pause / Cancel button again. Your new selection will
resume operation from the step in the previous
program (For example, if the previous program was
in rinsing step, the new one will also start from the
rinsing step). If you want to run the newly selected
program from the very beginning, you have to apply
the cancellation process first and then select a new
program.