Continental CP43609 Coffeemaker User Manual


 
15 16
GB
GB
GB
GB
• Put on the cover (21) on the espresso pot (22). Put the espresso pot
on the grid in the collection tray and bring the notch in the cover under
the opening of the espresso filter holder (23).
• Connect the power plug (10) with a corresponding electrical outlet.
• Press the switch I O (13) of the espresso machine to position I. Turn
the steam and espresso controller (19) on the espresso position. The
power indicator in the switch I O indicators on and the brewing process
starts.
• After approx. 2 -3 minutes the water is heated up and espresso coffee
pours into the espresso pot.
• If the filled water quantity is passed, turn the steam and espresso
controller (19) on position O and turn the switch I O (13) to position O
to turn the device off. The power indicator in the switch goes out.
Note for the preparation of cappuccino: The water quantity for the
preparation of cappuccino is larger. Fill in water for 2 cups of
cappuccino between the marking 2 and 4 at the espresso pot. Pour
water for 4 cups until lower end of the metal strap.
• Espresso coffee can be poured now. Hold the pot only at the handle (26).
Danger of burns!
• Caution! Let off the remaining steam by the steam nozzle (17)
before the filter holder is removed or the lock of the water tank is
opened. Turn the steam and espresso controller (19) in the
direction of slowly.
Milk foaming (for cappuccino)
• Prepare espresso as described above. Ensure that sufficient amount
of water is filled in for foaming up the milk after the preparation of
espresso in the water tank of the espresso machine (2) (The lower
area of the metal ring at the espresso pot corresponds to 4 cups of
espresso plus steam to foam up milk for cappuccino).
• The milk can be foamed up after the espresso is prepared.
• Fill into a heat-resistant vessel approx. 100 ml of milk and hold it under
the steam nozzle (17). Consider that approximately the double volume
of the cold milk is produced if the milk is foamed up. The steam nozzle
should always be dipped under the surface of the milk since otherwise
milk could splash out of the vessel. Dive the steam nozzle briefly
under the surface of the milk but not too deep. When the volume has
been doubled, dive the steam nozzle more deeply into the milk to heat
up approx. 65 - 75 C.
Note: Do not boil the milk. You recognize this if the volume suddenly
rises and great bubbles form.
• Turn slowly to the left the steam and espresso controller (19) from the
position 0 to position steam Control the steam strength by the
steam and espresso controller. The maximum amount of steam leaves
if the steam and espresso controller is turned in the direction of
until stop. The steam is pumped out into the steam nozzle and the milk
can be foamed up.
• As soon as enough milk is foamed up turn back the steam and
espresso controller to position O and turn the switch I O (13) of the
espresso machine to position O.
CAUTION! Turn back the steam and espresso controller to position O
before you take the vessel with the milk of the dipped steam nozzle.
Danger of burns!
CAUTION! Do not open the cover of the steam pressure vessel (1)
after the steam production until the rest steam was let off by the steam
nozzle completely, the rest steam can lead into injuries by the
espresso machine.
Coffee preparing
Open up the cover of the coffee machine (3). Fill the desired cup
number of water into the water tank of the coffee machine (4). The cup
number is marked at the glass pot. Never fill the water tank beyond
the marking 10 (10 cups of coffee).
• Turning the filter holder (7) aside and insert the permanent filter (6)
into the filter holder. The permanent filter has a handle (5) and for easy
inserting and taking out. Put the handle down after inserting.
• Put in the required amount of coffee powder into the coffee filter with the
measuring spoon (28) and swivel back the filter holder until it clicks in.
• Put the coffee pot (32) with a closed pot cover (31) on the warming
plate (8). Push it with an easy pressure under the drip stop (8). Make
sure that the drip stop (8) is pushed up completely, i.e. the coffee pot
is even and complete on the warming plate (11).
• Connect the power plugs (10) with a fitting electrical outlet.
• Turn the switch I O (12) to position I. The power indicator in the switch
lights on and the brewing process starts.
• While the coffee is made in the coffee pot, it can be taken from the
device for a short time since the coffee machine is equipped with a
drip stop system. Put the coffee pot back on the warming plate within
30 seconds to avoid overrunning the coffee.
• While the switch I O (12) in the position I is, the warming plate is
heated up to keep the coffee warm. After the device is switched off,
the warming plate keeps warm for a certain time. Danger of burns!
When the complete water passed, turn the switch I O (12) to position
O. The power indicator in the switch I O goes out and the device is
turned off.
• Unplug the power plug from the electrical outlet after the brewing
process.
• The pot can be taken out from the device and coffee can be poured.
Hold the coffee pot only at the handle (29) tightly since the glass heats up.
• Press the rocker lever (30) to open the coffee pot cover.
• The coffee pot can be pushed back onto the warming plate for keeping
the coffee warm in the coffee pot.
Caution! The device may not remain unattended and switched on for
some time to heat up the warming plate. This can lead to damages to
the device and at the coffee pot.
53 54
• Ponga la cantidad adecuada de café exprés en el filtro con la cuchara
de medir (28). Considere las marcas en el filtro de espresso.
• Presione suavemente el café con el extremo de la cuchara de medir
(27). No obstante, no presione demasiado porque podría causar
congestión y desbordamiento. Retire el excedente de café del filo del
filtro de espresso para asegurar una buena fijación al soporte del filtro.
La marca de tope no debe ser excedida.
• Retire el cierre del filtro (25) con el pulgar e inserte el soporte del filtro
de espresso desde abajo en su soporte (18). El asa (26) del soporte
del filtro de espresso debe mostrar la flecha Gire el asa del
soporte del filtro de espresso hacia la derecha a la posición LOCK
hasta detenerse.
• Ponga la bandeja de goteo (15) con una rejilla insertada (16) en su
soporte (14).
• Ponga la cubierta (21) en la cafetera de espresso (22). Ponga la
cafetera de espresso en la rejilla de la bandeja de goteo y lleve la
muesca de la tapa bajo la apertura del soporte del filtro de espresso
(23).
• Conecte el cable de corriente (10) a una toma adecuada de corriente.
• Presione el interruptor I O (13) de la máquina de espresso a la
posición I. Coloque el control de vapor y de espresso (19) en la
posición de espresso.
El indicador de potencia de los indicadores de I O se encenderá y
comenzará el proceso de preparación.
• Tras aproximadamente 2 o 3 minutos, el agua se calentará y el café
exprés empezará a verter sobre la cafetera de espresso.
• Cuándo todo el agua agregada haya pasado, coloque el control de
vapor y de espresso (19) en la posición de O y el control I O (13) en la
posición O para apagar el aparato. El indicador luminoso de potencia
en ese botón se apagará.
Nota para la preparación del capuchino: La cantidad de agua para
preparar el capuchino es mayor. Para hacer 2 tazas de capuchino,
rellene de agua hasta quedar entre la marca de 2 y de 4 en la
cafetera de espresso. Vierta agua para 4 tazas, hasta el final inferior
del asa metálica.
• El café exprés ya puede ser servido. Sostenga la cafetera únicamente
por su asa (26). ¡Peligro de quemaduras!
¡Precaución! Deje un tiempo al vapor que aún queda en la
boquilla de vapor (17) antes de retirar el soporte del filtro o de
abrir el cierre del depósito de agua. Gire el control de vapor y de
espresso (19) en la dirección de despacio.
Leche espumosa (para el capuchino)
Prepare espresso como se describe arriba. Asegúrese de que rellena
el depósito de agua de la máquina de espresso (2) con la cantidad
suficiente de agua para hacer espuma de la leche después de la
preparación de espresso. (La zona menor del anillo de metal en la
cafetera de espresso se corresponde con 4 tazas de espresso más
vapor suficiente para hace espuma de la leche para el capuchino).
• La leche se puede hacer espumosa después de haber preparado el
espresso.
• Rellene un recipiente resistente al calor con aproximadamente 100ml
de leche y sosténgalo bajo la boquilla de vapor (17). Considere que
aproximadamente se duplica el volumen de leche cuándo se hace
espumosa. La boquilla de vapor siempre debe estar sumergida bajo la
superficie de la leche ya que de otra manera la leche podría salpicar
fuera del recipiente. Sumerja la boquilla de vapor levemente bajo la
superficie de la leche. Cuándo el volumen se haya doblado, sumerja
la boquilla más profundamente para calentarla entre 65º C y 75º C.
Nota: No hierva la leche. Sabrá cuándo sucede eso si el volumen
crece repentinamente con grandes burbujas.
• Gire despacio hacia la izquierda el control de vapor y de espresso (19)
desde la posición 0 hasta la posición de vapor Controle el nivel de
vapor con el control de vapor y de espresso (19). Saldrá la máxima
cantidad de vapor cuándo dicho control esté girado en la dirección de
hasta que se detenga. El vapor es bombeado hacia la boquilla de
vapor y la leche puede ser hecha espuma.
• Tan pronto como haya convertido en espumosa la suficiente leche,
retorne el control de vapor y espresso a la posición O y pulse el
interruptor I O (13) de la máquina exprés a la posición O.
• ¡PRECAUCIÓN! Retorne el control de vapor y espresso a la posición
O antes de retirar el recipiente con la leche de la boquilla de vapor.
¡Peligro de quemaduras!
• ¡PRECAUCIÓN! No abra la tapa del recipiente de presión de vapor (1)
después la producción de vapor hasta que los restos de vapor hayan
desaparecido completamente de la boquilla de vapor. Dichos restos
podrían causarle heridas o daños.
Preparando café
Abra la tapa de la máquina de café (3). Rellene de agua con el
número deseado de tazas en el depósito de agua de la máquina de
café (4). El número de la taza está marcado en el recipiente de cristal.
Nunca rellene el depósito de agua por encima del nivel de 10 (10
tazas de café).
• Gire el soporte del filtro (7) a un lado e inserte el filtro permanente (6)
en el soporte. El filtro permanente tiene un asa (5) para facilitar el
insertado y la retirada. Baje el asa antes de insertar.
• Coloque la cantidad requerida de café en el filtro de café con la
cuchara de medida (28) y gire el soporte del filtro hasta que haga clic.
• Coloque la cafetera (32) con la tapa cerrada (31) en el plato para
conservar la temperatura (11). Presiónelo con una presión sencilla
sobre el freno de goteo (8). Asegúrese de que el freno de goteo (8) es
presionado por completo hacia arriba, es decir la cafetera esta
nivelada y colocada sobre el plato de mantener la temperatura (11).
• Conecte el enchufe (10) a una toma de corriente.
• Presione el interruptor I O (12) a la posición I. La luz indicadora en el
interruptor se encenderá y comenzará el proceso.
• Mientras el café se está haciendo en la cafetera, se puede retirar
E
E
E
E