DeLonghi EC860 Coffeemaker User Manual


  Open as PDF
of 16
 
9
Instructions for use
programming menu, press button again.
Setting the temperature
To modify the temperature (low, medium, high) of the water
used to make the coee, proceed as follows:
1. Accesstheprogrammingmenu;
2. Keep button pressed until the lights relative to the
wanted temperature turn-on (see chart below).
3. When the lights relative to the wanted temperature turn-
on, release the button.
4. Press to turn the appliance o (stand-by).
Adjust Stand-by
The machine is pre-set to switch to stand-by after 75 minutes
of non-use.This timeintervalcan bemodied sothat the
appliance switches o after 15 minutes or after 3 hours.
Proceed as follows:
1. Accesstheprogrammingmenu;
2. Keep the button pressed until the lights relative to
the desired stand-by interval turn-on(see chart below).
3. When the lights relative to the wanted stand-by interval
turn-on, release the button.
4. Press to turn the appliance o (stand-by).
“Setting temperature” and “Adjust Stand-by” chart
Temperature Corresponding lights Stand-by after
Low
15 minutes
Medium
75 minutes
High 3 hours
Set the water hardness
The lights signaling the need to descale the appliance, after
a pre-set period of operation depends on the hardness of the
water.Itispossibletoprogramthemachineaccordingtothe
actual water hardness in use in the area, thus making descaling
less frequent. Proceed as follows:
1. Remove the provided reactive strip“TOTALHARDNESS
TEST” from its packaging.
en
Activation of the water lter and lling of the water
tank
• Removethelterfromthepackagingandrinseitwith
about17OZ/0.5Lofrunningwater(g.2).
• Turnthecalendardisc(seeg.3)untilthefollowing2
months of use are displayed.
Please note
thelterhasatwomonthdurationiftheapplianceisused
normally, whereas if the machine remains unused with the
lterinstalled,ithasamaximum3monthduration.
• Removethewatertankandllitwithfreshwater(donot
exceedtheMAXline)(g.4).
• Completelydipthelterinthewater,tiltingittoenable
airbubblestocomeout(g.5).
• Insertthelterintheappropriateseat(g.6),pressdown
and close the tank with the lid.
• Placethetankbackintothemachine(Ensurethewater
levelisnotovertheMAXline)(g.7).
Thelterisnowactivatedandthemachinecanbeused.
Appliance rst use
• TurntheapplianceonbypressingtheI/Omainswitch
A3atrearinpos.I:theapplianceperformsaself-test,
signalled by the sequential ashing of the lights.
•
Once the self-test is completed, the “hot water spout” light
B8asheswhiletheothersturn-o:theappliancesignals
itisnecessarytoinsertthehotwaterspout(g.8).
• Placeacontainerunderneaththespoutwithminimum
capacityof100ml(g.9).
• Pressthe“hotwater”button : delivery starts and
interrupts automatically.
• Thecoeeandwaterspoutlightsashtoindicatethe
appliance is reaching temperature: when the lights stop
ashing and remain permanently on, the appliance is
ready for use.
Please note: upon rst use
• Iflights and ash, press the button
again.
• Upon rstuse, it isnecessary to make 4-5coees or
4-5 cappuccinos before the machine gives a satisfying
results.
Settings of the programming menu
To access the programming menu, ensure the appliance is
in stand-by, simultaneously press buttons
and
untiltheON/Stand-by(B2)lightashes:theapplianceisin
programmingmode.Setthemachineaswanted;toexitthe
 previous next