DeLonghi EC860 Coffeemaker User Manual


  Open as PDF
of 16
 
13
Cleaning the drip tray
Attention!
The drip tray is equipped with a oating water level indicator
(red) (A11). As soon as this indicator starts protruding from
the cup tray, empty the tray and clean it, otherwise the water
may overow and damage the machine, and the surrounding
work-top.
1. Removethedriptray(g.26).
2. R
emovethecuptray,disposeofthewater(g.27)and
clean the tray using a cloth: then re-assemble the drip tray.
3. Re-insertthedriptray.
Cleaning the coee lters
Regularlycleanthecoeeltersrinsingthemunderrunning
water.Checkthattheholesarenotblocked.Iftheyare,clean
themusingapin(g.28).
Cleaning the boiler outlet
Rinsetheboileroutletevery200coeesdelivered,bydelivering
0.5l of water from the boiler outlet (place a cup under the
boiler outlet and then press either the 1 or 2 cup coee button
to deliver a coee without using coee powder).
Cleaning the milk container
Clean the milk container after each milk preparation, as
described below:
1. Extract the lid.
2. Removethemilkspouttubeandtheintaketube(g.29).
3. Removethefrothregulatorbybypullingitout(g.30).
4. Carefully clean all components using hot water and a mild
detergent. All components can be washed in the
dishwasher by positioning them on the upper rack
of the dishwasher. Pay particular attention that milk
residues do not remain inside the holes and in the groove
on the narrow part of the froth regulator.
5. Also check that the intake tube and the milk spout tube
are not obstructed by milk residues.
6. Re-assemblethefrothregulator,themilkspouttubeand
the milk intake tube.
7. Place the lid on the milk container.
Replacing the lter
After two months of duration (see calendar), or if the appliance is
notusedfor3weeks,replacethelterasdescribedinparagraph
“Activationofthesoftenerlterandllingofthetank”(page9).
Descaling
Descale the machine when the light  ashes on the
control panel. Proceed as follows:
1. Removethewaterlter.Fillthetankwiththedescaling
solution obtained by diluting the descaler with water as
indicated on the descaler pack.
2. Insertthehotwaterspout(g.8).
3. Place one container under the boiler outlet and one under
thehotwaterspout(g.31)andensurethedriptrayis
empty and correctly inserted.
4. Simultaneously press the and
buttons
: light
turns on (if the hot water spout has not been
inserted, the light ashes).
5. Press the  button. Descaling is signaled by the
LEDthatalternateinsequence.Thedescalingprogram
automatically performs a series of deliveries from the
boiler outlet and from the hot water spout at intervals, to
remove the lime scale from inside the coee machine.
6. Once the descaling solution is terminated, the light
turns on to indicate rinsing is necessary.
7. To eliminate the solution and lime scale residues, rinse the
tankandllitwithfreshwater(withoutdescaler);empty
the containers and place them under the boiler outlet and
hot water spout.
8. Press the button:rinsingstartsandallLEDsashin
sequence.
9. Rinsingstopswhenthetankisempty:rinseandrellthe
tank.
10. Light turns on: press the relative button: delivery
starts and interrupts automatically.
The appliance is now ready for use.
Repairstothecoeemachinerelativetolimescaleproblems
are not covered by the warranty if the descaling procedure
described above is not performed on a regular basis.
en
Instructions for use
 previous next