DeLonghi EC860 Coffeemaker User Manual


  Open as PDF
of 16
 
12
2. Place a cup or other container under the milk spout tube.
3. Keepthe“CLEAN”button(g.25)pressed:lights
and
ash. When the lights stop ashing and the
appliancegoesbacktoreadyforuse,releasethe“CLEAN”
button: the steam cleans the circuits inside the milk
frother.
Program the amount of coee and milk in the cup for
cappuccino or milk
The machine has been set by default to deliver standard amounts
ofcoeeandmilk.Ifyouwouldliketoamendthesequantities,
proceed as follows:
1. Place a cup under the coee spouts and the milk spout
tube.
2. Press the button relative to the preparation with milk to
be programmed and keep it pressed. After a few seconds,
the machine starts delivering the milk.
3. Once the required quantity of milk has been delivered into
thecup,releasethebutton;milkdeliverystops.
4. Program the amount of coee into the cup as for the
amount of milk.
5. Programmingisconrmedbythe lightsashing for3
seconds.
The machine is now re-programmed according to the new
amounts of milk and coee.
Preparing the hot water and steam
Scalding hazard!
Donot leavethemachine unattendedwhendeliveringhot
water. The spout heats up during delivery, therefore, only the
black part must be held.
Delivering hot water
1. Checkthehotwaterspoutiscorrectlyattached(g.8).
2. Place a cup under the spout (as near as possible to avoid
sprays).
3. Press the button(B7):therelativelightashesand
the appliance starts hot water delivery.
4. The machine automatically stops delivery.
Please note!
• Tomanuallyinterruptthehotwaterdelivery,press
button again.
Programming the amount of water automatically
delivered
Ifyouwouldliketoamendtheamountofwatersetbydefault,
proceed as follows:
1. Place a cup under the water spout.
2. Keep the button pressed.
3. When the hot water in the cup reaches the required level,
release thebutton. Programmingis conrmed by the
lights ashing for three seconds.
The machine is now re-programmed according to the new
amount.
Delivering steam
1. Checkthehotwaterspoutiscorrectlyattached(g.8).
2. Fill a container with the liquid to be heated/frothed and
immerse the water/steam spout into the liquid.
3. Press twice the button(B7):therelativelightashes
and the appliance starts steam delivery.
4. When the required temperature is obtained, interrupt
steamdeliverybypressingthebuttonagain.(Youshould
not discharge steam for more than 3 minutes at a time).
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Cleaning the water spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and press
the buttontodeliveralittlewater(g.3).
Stop the ow of water by pressing the button
again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout.
3. Checktheholeisnotblocked.Ifnecessary,cleanwitha
pin.
4. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
5. Reinsertthewaterspout.
Cleaning
Attention!
• Do notusesolvents,abrasive detergentsor alcoholto
clean the machine.
• Onlythemilkcontainer(D)canbewashedinthedish
washer. No other part of the appliance can be washed in
the dishwasher.
•
Do notuse metalobjects to remove coee depositsor
fouling as they might scratch the metal or plastic surfaces.
en
Instructions for use
 previous next