Filter
Top Products
10
Ⅲ Select a coffee product. For example, ristretto (Fig. 1/C)
2 RISTRETTI
Ⅲ The machine will now make two ristrettos in one brewing step.
11. Making hot water
COFFEE READY
Ⅲ Place a cup under the pivoting hot water spout (T) and press the
Hot Water key (T/ ).
HOT WATER
Ⅲ The machine stops dispensing the programmed portion of hot
water automatically.
A bargraph indicates the duration of the hot water dispensing
process.
To stop the machine from dispensing hot water prematurely,
press any of the product keys.
There might be some initial splashing when drawing off hot
water. The pivoting hot water spout becomes hot. Avoid
direct contact with the skin!
12. Drawing off steam
COFFEE READY
Ⅲ Place a cup under the pivoting steam spout (V) and press the
Steam key (S / ).
STEAM
Ⅲ The machine stops dispensing the programmed portion of steam
automatically.
A bargraph indicates the duration of the steam dispensing
process.
To stop the machine from dispensing steam prematurely,
press any of the product keys.
There might be some initial splashing when drawing off
steam. The pivoting steam spout becomes hot. Avoid direct
contact with the skin!
13. Switching the machine off
COFFEE READY
Ⅲ Switch the machine off using the ON / OFF key (Fig. 5/A). The
machine automatically performs a rinsing cycle when you switch
it off. Only the spouts and nozzles that were used are rinsed.
GOOD-BYE
Use the power switch on the rear of the machine (Fig. 15/D)
to disconnect the machine from the mains supply.
14. Programming
The following parameters can be programmed:
¼ Water hardness
¼ Setup (product)
¼ Time
¼ Switch-on time
¼ Switch-off time
¼ Language
¼ Display (unit and time format)
¼ Information (number of products made, number of cleaning
cycles run)
14.1 Adjusting the machine to the water hardness
For this, please refer to Chapter 8 “Adjusting your machine
to the water hardness”.
14.2 Customizing (product definition)
You can program each product according to your preference.
Example: cappuccino
COFFEE READY
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
Ⅲ Press the «+» or «–» key until SETTING appears on the display.
SETTING
Ⅲ Press P again (Fig. 5/E) to activate the SETTING programming
step.
SETTING
PLEASE
SELECT
Ⅲ Select a product key of your choice. In our example it is cappuc-
cino (Fig. 1/E).
CAPPUCCINO
WATER
100 ML
Ⅲ Press P (Fig. 5/E) again to activate the setting programming step.
Ⅲ Press the «+» or «–» key until the required amount of water
appears on the display.
Ⅲ Press P (Fig. 5/E) to confirm your setting.
CONFIRMED
CAPPUCCINO
FROTH
20 SEC
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
Ⅲ Press the «+» or «–» key to define the amount of frothed milk.
Ⅲ Press P to confirm your setting (Fig. 5/E).
CAPPUCCINO
MILK
20 SEC
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
Ⅲ Press the «+» or «–» key to define the amount of frothed milk.
Ⅲ Press P to confirm your setting (Fig. 5/E).
Ⅲ Press the «+» or «–» key until POWDER appears on the display.
CAPPUCCINO
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
Ⅲ Press the «+» or «–» key to set the coffee strength.