Filter
Top Products
14
16.8 General cleaning instructions
Ⅲ Never use sharp objects or caustic chemicals for cleaning.
Ⅲ Clean the inside and outside of the case using a soft, damp cloth.
Ⅲ Clean the pivoting steam spout (V) each time it was used.
Ⅲ After heating milk, draw off some steam to clean the inside of
the pivoting steam spout (V).
Ⅲ The water tank should be rinsed out and filled with fresh water
daily.
Visible calcification in the water tank can be removed using
a commercial decalcifying agent. Take out the water tank
(Fig.2).
If you are using a CLARIS plus filter cartridge, remove it
before decalcifying the tank.
16.9 Disassembling and cleaning the dual spout
We recommend to disassemble and clean the dual spout if
you make milk products regularly.
Ⅲ Remove the cover of the height-adjustable dual spout by pressing
the Unlock key (Fig. 12) and remove the coffee distributor (Fig.
13).
Ⅲ Take off the spouts (Fig. 13).
Ⅲ Take the spouts apart (Fig. 14).
Ⅲ Thoroughly rinse all the parts with warm water.
Ⅲ Reassemble the parts (Fig. 14).
When assembling the dual spout, note the colour of the indi-
vidual parts (Fig. 14).
Ⅲ Attach the spouts to the IMPRESSA X9 (Fig. 13).
Ⅲ Put back the cover, making sure it locks into place (Fig. 13).
Use corresponding brushes for carrying out the cleaning
steps described in sections above.
16.10 Cleaning the milk system
We recommend to clean the milk system daily.
Once started, the cleaning process must not be interrupted. It takes
approx. 2 minutes.
Ⅲ Open the programming door on the front (Fig. 4).
Ⅲ Press the Clean Milk System key (Fig. 5/H) until you hear an
acoustic signal.
CLEANER FOR
PRESS
KEY
Ⅲ Place a receptacle with a capacity of at least 0.5 litres under the
height-adjustable dual spout (Fig. 6).
Ⅲ Fill a receptacle with approx. 4 dl of water and add 1 1/2 capfuls
of JURA cappuccino cleaning agent. Dip the two milk hoses into
this solution (Fig. 8/B).
Ⅲ Press the Clean Milk System key (Fig. 5/H).
MACHINE CLEA
Ⅲ You will hear an acoustic signal.
WATER FOR C
PRESS
KEY
Fill a receptacle with approx. 4 dl of fresh water and dip the
milk hoses into it (Fig. 8/B).
Ⅲ Press the Clean Milk System key (Fig. 5/H).
MACHINE CLEA
COFFEE READY
Always dip both milk hoses into the fluid (Fig. 8/B).
16.11 Cleaning the coffee system
Once started, the cleaning process must not be interrupted. It takes
approx. 15 minutes.
COFFEE READY
CLEAN
After having dispensed 220 products or after 80 rinsing cy-
cles, the machine must be cleaned. The machine will still
make coffee or hot water/steam. However, we recommend
that you run a cleaning cycle within the same day. After hav-
ing made another 20 coffees the cleaning alarm flashes, and
after yet another 20 coffees, the display will indicate the fol-
lowing message:
CLEAN NOW
Ⅲ Open the programming door (Fig. 4) and press the Clean Coffee
System key (Fig. 5/I) until you hear an acoustic signal.
EMPTY
TRAY
EMPTY
COFFEE
BIN
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
COFFEE BIN
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
PRESS
KEY
Ⅲ Place a sufficiently large receptacle under the height-adjustable
dual spout (Fig. 6).
Ⅲ Press the Clean Coffee System key (Fig. 5/I) until you hear an
acoustic signal.
MACHINE CLEA
Ⅲ You will hear an acoustic signal.
ADD TABLET
PRESS
KEY
Ⅲ Drop an original JURA cleaning tablet into the filler funnel
(Fig. 16).
Ⅲ Press the Clean Coffee System key (Fig. 5/I).
MACHINE CLEA
Ⅲ You will hear an acoustic signal.
EMPTY
TRAY
EMPTY
COFFEE
BIN
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
COFFEE BIN
MISSING