Filter
Top Products
metal centrifugal juicer
Use the centrifugal juicer for making juice from firm fruit
and vegetables.
ቢ pusher
ባ centrifugal lid
ቤ pulp remover
ብ filter drum
ቦ juicer drive shaft
to use the centrifugal juicer
1 Fit the juicer drive shaft and bowl onto the power unit.
2 Place the pulp remover ቤ into the filter drum ብ - ensuring
the tabs locate with the slots in the bottom of the drum .
3 Fit the filter drum ብ.
4 Place the attachment lid ባ onto the bowl and turn until it
locks . Your juicer will not operate if the bowl or
lid are not fitted correctly into the interlock .
5 Place a suitable glass or jug under the juice outlet.
6 Cut the food to fit the feed tube.
7 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube. Process fully before
adding more.
●
After adding the last piece, let the juicer run for a further 30
seconds to extract all the juice from the filter drum.
safety
●
Do not use the juicer if the filter is damaged.
●
The cutting blades on the base of the filter drum are very
sharp, take care when handling and cleaning the drum.
●
Only use the pusher supplied. Never put your fingers in the
feed tube. Unplug before unblocking the feed tube.
●
Before removing the lid, switch off and wait for the filter to
stop.
important
●
If the juicer starts to vibrate, switch off and empty the pulp
from the drum. (The juicer vibrates if the pulp becomes
unevenly distributed).
●
Maximum capacity that can be processed at one time is
500g of fruit or vegetables.
●
Some very hard foods may make your juicer slow down or
stop. If this happens switch off and unblock the filter.
●
Switch off and clear the pulp collector regularly during use.
hints
●
Before processing remove stones and pips (eg pepper,
melon, plum) and tough skins (eg melon, pineapple). You
don’t need to peel or core apples and pears.
●
Use firm, fresh fruit and vegetables.
●
Citrus fruit - peel and remove the white pith, otherwise the
juice may taste bitter. For best results use the citrus juicer.
KENSTORE™ attachments carousel
Your food processor is supplied with an attachment storage
carousel that fits inside the bowl.
to use the storage carousel
1 Fit the knife blade to the bowl.
2 Then fit the whisk, discs and canopy into the carousel .
3 Fit the carousel over the knife blade and place the processor
lid on top .
care & cleaning
●
Always switch off and unplug before cleaning.
●
Handle the blades and cutting discs with care -
they are extremely sharp.
●
Some foods may discolour the plastic. This is perfectly
normal and won’t harm the plastic or affect the flavour of
your food. Rub with a cloth dipped in vegetable oil to remove
the discolouration.
power unit
●
Wipe with a damp cloth, then dry. Ensure that the interlock
area is clear of food debris.
●
Store excess cord in the storage area at the back of the
power unit .
liquidiser/mini chopper/mill
1 Empty the goblet/jar before unscrewing it from the blade
unit.
2 Wash the goblet/jar by hand.
3 Remove and wash the seals.
4 Don’t touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
twin beater geared whisk
●
Detach the beaters from the drive head by gently pulling
them free. Wash in warm soapy water.
●
Wipe the drive head with a damp cloth, then dry.
Do not immerse the drive head in water.
centrifugal filter drum
●
Lift out the pulp remover and tap lightly to release the pulp.
●
Clean using a soft brush.
●
Check the filter regularly for signs of damage. Do
not use if the filter is damaged. Refer to “service
and customer care”.
6