Filter
Top Products
65
9. ADJUSTMENT AND SETTING OF THE
DOSE (where available)
9.1. Models SDE
It is possible to adjust the dose of coffee and hot water
dispensed by electronically controlled models.
9.1.1. Adjusting the dose
The quantity of coffee and hot water dispensed can
be adjusted using the button panel or the hot water
controls.
1 Press the button E on any button panel and hold it
down for 8-10 seconds until water stops flowing
from the dispensing unit and the led of the
continuons button on the first button panel on the
left begins flashing.
2 It is necessary to act as to make 1 or 2 cups in
order to reach the correct coffee amount
adjustment in the cup.
3 Put the filter-holder (with ground coffee) on the left
unit and the cup under the spout.
4 Operate the selected button (i.e. button A for one
small cup).
5 One the required coffee amount in the cup has
been reached, press the stop button E. Coffe will
stop pouring and the microprocessor will store the
dose.
6 Press the continuous button E again; the led will
go out and the machine will store the new quantity.
7 Make the coffee and check the cup amount in order
to check that programming is correct.
If some doses have to be changed (B-C-D), once at
point 5 repeat the instructions in points 3-4-5 for each
dose, remembering to use the filter-holder with
relevant filter and freshly ground coffee.
Then carry out point 6 and repeat point 7 to check all
changed doses.
If all units are to be programmed with the same doses,
the selection of coffee doses is finished. If the dosage
of another unit is to be changed (1-2-3-4 doses),
proceed as indicated in the above-mentioned point
1-7, using only the button panel of the selected unit.
9.1.2. Adjusting the quantity of hot water
Proceed as follows:
1 Press the continuous E button on any button panel
and hold down for 8-10 seconds until water stops
flowing from the dispensing unit and the led of the
E button on the first button panel on the left starts
flishing. The machine is ready to accept quantity
variations.
8.4. Preparing tea, camomile, etc.
Place the jug under the hot water spout and use
the delivery control according to the model (Fig.8).
When the desired quantity has been obtained, turn
off the switch.
Add the beverage desired.
Models SDE
For these models, hot water is dispensed in specific
measures (see paragraph 9, adjusting the dose of
hot water).
To dispense hot water in different quantities, proceed
as follows:
Hold down the delivery control 4-E Fig.8 for at least
four seconds then release the button; the machine
continuously delivers water.
When the desired measure has been obtained,
press the button E again to interrupt delivery.
When the dose of hot water is being delivered
electronically, delivery can be interrupted by pressing
the button E.
When purified water is used, these beverages often
assume a darker colour.
Should the user prefer a lighter coloured drink, draw
fresh water from an ordinary tap and proceed with
the heating phase as described in point 8.3.
Continuously move the jug up and down so that
the nozzle moves in and out of the milk, causing it
to froth.
Turn off the steam tap and pour the milk into the
cup.
Immediately after carrying out this operation,
clean the spout with a sponge or a clean cloth
so that the milk does not dry on it. Be careful
as the spout is hot and may burn your hand.
8.3. Heating a beverage
Immerse the steam spout into the liquid to be
heated.
Gradually turn on the steam tap 7 Fig.8; the steam
that bursts in the liquid heats it to the desired tem-
perature.
Turn off the steam tap when the desired tempera-
ture has been reached.
Immediately after carrying out this operation,
clean the spout with a sponge or clean cloth.
Be careful as the spout is hot and may burn
your hand.