Filter
Top Products
30
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
4. To Remove Ignition/light Switch
Remove the Control Panel - see 1.
NB. The old switch may be destroyed during removal.
Remove the old switch from its bezel by griping the
switch body behind the control panel and twisting
sharply. The switch bezel can then be removed by
folding back its locking wings and pushing forward. Fit
the new bezel to the control panel by first lining up the
raised key on its body with the cutout in the control
panel and pushing it in from the front. Assemble the
new switch to the bezel by lining up the key sections
and pushing home. Fit the new button by pushing in
from the front.
Replace Control Panel in reverse order and test for
ignition.
5. To Remove Clock
Disconnect from electricity supply.
Remove the Control Panel (See 2). Pull off the timer
control button(s).
Remove the timer/mounting bracket assembly from the
control panel by removing the fixing screws.
Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the
same time pulling the unit forward.
Reassemble in reverse order. When replacing leads
refer to the wiring diagram. Check operation of timer.
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS TURN OFF GAS SUPPLY.
6. To Remove a Thermostat
Remove RH hotplate tray. (For L H oven remove L H
side panel - see 2.) Open appropriate oven door.
Unclip the thermostat phial from the clips at the front
of the oven roof. Disconnect tubing nut at rear of
thermostat and remove the screw(s) securing the
thermostat to the gas rail. Remove thermostat and
gasket/seal. When fitting replacement thermostat use
the new gasket/seal supplied.
Ensure that the capillary is clipped to the bracket at
the front of the oven roof.
Reassemble in reverse order. Check appliance is gas
sound. Check operation of thermostat.
7. To Change Grill Control Tap
Remove the facia panel, see 2. Lift up the RH hotplate
tray front (see 2). For LP cookers, unplug the FSD lead
from the rear of the tap. Undo the gas connection to
rear of valve and remove the screw(s) securing tap to
gas rail. Remove old tap, discard old gasket/seal. Fit
new gasket/seal to new tap.
Reassemble in reverse order. Check tap is adjusted for
correct gas. Check appliance is gas sound.
8. To Change Warmer Switch
Remove RH hotplate tray. (see 4). Disconnect wiring
from Warmer switch. Remove 2 screws holding switch
to mounting panel, taking care not to lose the switch
rotation limiter. Fit new switch and reassemble in
reverse order. Check for correct operation.
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS TURN OFF GAS SUPPLY.
9. To Change Hotplate Control Tap
Remove the facia panel, see 2. Lift up the LH hotplate
tray front (see 2). Remove the heat shield (2 screws).
Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove the
fixings that secure the tap to the gas rail. Remove
the tap. Remove and discard the gasket seal. Fit
new gasket seal to replacement tap. Re-assemble
in reverse order. Check the appliance is gas sound.
Check hotplate ignition.
10. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new
injector. Reassemble in reverse order. Check appliance
is gas sound.
11. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically
up sufficiently to grip the lead between thumb and
forefinger. Pull off the electrode, but keep hold of the
lead. Fit new electrode to the lead. Fix electrode in
burner with screw. Replace burner cap. Check the
burner ignition. Replace pan supports.
12. To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
LH hotplate burners
Remove heat shield (2 screws). The burners are
mounted in 2’s on cross supports. Disconnect the
burner feed pipes at the burners. Remove the screw
on the right holding the cross support. Slide the
support to the right to release in from the left hand
location. Lift the cross support and burners clear. The
burners are fixed to the cross supports with 2 screws
Remove the appropriate burner and fit the new one.
Reassemble in reverse order. Check burner operation
is satisfactory.
RH High burner
Disconnect the burner feed pipes at the burner. Fit
the new one and reassemble in reverse order. Check
burner operation is satisfactory.