Filter
Top Products
To check the actual and set temperatures:
!l!l
1. Press the FRZ TEMP or REF TEMP Pad.
The signal light on the pad you
pressed and the ACTUAL signal light
q
will come on. The actual refrigerator
or freezer temperature will be dis-
played. (This is the average air tem-
w
perature in the compartment.)
2. Press the SET TEMP Pad. The SET signal
light will come on and the set tem-
perature will be displayed. You may
set freezer temperatures from
5°F
(-21°C) to 8°F (--13°C) and re-
frigerator temperatures from 33-F
(1°C) to 42°F (6°C).
NOTE: If the actual freezer temperature is above
the display range, a flashing 8 will show on the
display. If the actual refrigerator temperature is
above the display range, a flashing 42 will show
on the display.
To change the refrlgerafor or freezer
temperatures:
The refrigerator and freezer temperatures are
preset at 36°F (2”CJ and 0°F (-f8”CJ. If you wish to
change these temperatures do the following:
Eu
1. Press the FRZ TEMP or REF TEMP Pad.
The signal light on the pad you
pressed will come on and the
actual refrigerator or freezer
temperature will be displayed.
2. Press the SET TEMP Pad The SET sia-
nal light will come on and the pr&
set temperature will be disptayed.
0
A
3. Press the A Pad to raise the tem-
perature setting or press the V Pad
Hi
to lower the temperature setting.
You must press these pads within IO
seconds of pressing the SET pad or
you will have to press SET again.
NOTE: Two beeps will sound to indicate an error
if you attempt to set a temperature past the re-
frigerator or freezer temperature range.
Two beeps will sound to indicate an error if
you press the arrow pads without pressing the
SET pad.
To return to preset temperatures (AUTO TEMP):
i. Press the AUTO TEMP Pad.
2. The signal light will come on for IO
seconds to show that the tem-
perature has been set, then the light
will turn off.
Using AUTO TEMP will set the freezer temperature
to O’F ( - 18°C) and the refrigerator to 36°F (2°C).
To set MAX FRUICE and MAX REFICOOL:
The MAX FRZ/ICE Pad will set the freezer to-10°F
( 23’C) for 24 hours. The MAX REF/COOL Pad will
set the refrigerator to 33°F (I%] for 24 hours. Either
compartment can be set independently for max-
imum cooling. MAX FRZ/ICE can also be used for
maximum ice production. After 24 hours, the tem-
peratures will return to the earlier settings.
1. Press the MAX FRZ/ICE or
MAX REF/COOl Pad. The
signal light on the pad
you pressed will come
on.
Pad. -
NOTE: Each time you press a maxlmum cooling
pad a new 24 hour cycle will start.
Electronic display warning signals...
The five signal lights on the right side of the Elec-
tronic Control Center will show if an action is
needed or if there is a problem.
DOOR AJAR (red flashing light)
l
The DOOR AJAR light flashes when either door is
open.
. Eight beeps sound when either door is open for
longer than 3 minutes. Beeps are heard every
2 minutes until door(s) are closed.
WARM (red flashing light)
l
The WARM light flashes when the refrigerator and/
or freezer temperature(s) are above 48,‘F/15’F
(9”C/ - 9°C).
l
Eight beeps sound every 2 minutes.
l
The FRZ TEMP and/or REF TEMP signal light(s) will
also flash to show which compartment is too
warm.
l
Open compartment door(s) less often. Check the
set temperatures.
6
WARM (red light)
l
The WARM light is on when refrigerator and/or
freezer temperature(s) were above 48”F/15”F
(9”C/ - 9°C) but are now in a safe temperature
range.
l
The FRZ TEMP and/or REF TEMP signal light(s) will
also stay on to show which compartment was
too warm.
l
The signal lights can be turned off by pressing
the RESET Pad.
CHECK FOOD (red flashing light)
l
The CHECK FOOD light flashes when refrigerator
and/or freezer are above safe temperature(s)
and have been for 4 hours or more.
. The WARM, FRZ TEMP and/or REF TEMP signal lights
will also flash.
l
Check food for spoilage. Check the set
temperature.
* Call for service, if necessary.