Filter
Top Products
2
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years
or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially
free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period.
This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment,
has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or
casualty. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by
telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping
the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the
defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to
make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not
constitute warranties and should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the
equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor
warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service
Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT,
WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO
REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of
equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any
other special, incidental or consequential damages.
CONTENTS
Warranty ..................................................................................................................................... 2
Introduction ................................................................................................................................ 3
User Notices ............................................................................................................................... 3
Electrical Requirements .............................................................................................................. 4
Plumbing Requirements ............................................................................................................. 4
Initial Set-up ............................................................................................................................... 5
Electrical Hook-up ...................................................................................................................... 5
Plumbing Hook-up ..................................................................................................................... 5
Setting Dispenser Flow Rate ...................................................................................................... 6
Selecting the Correct Pump Tubing ............................................................................................ 7
Operating Controls & Interface ................................................................................................... 8
Initial Fill & Heat ......................................................................................................................... 9
FlavorGard™ Feature ................................................................................................................ 10
Rinse Alarm Feature ................................................................................................................. 11
Brew Temperature Lockout Feature .......................................................................................... 11
Programming the Dispenser Flow Rate .................................................................................... 12
Loading the Concentrate .......................................................................................................... 17
Priming the Concentrate Lines ................................................................................................. 17
Operating the Dispenser ........................................................................................................... 18
Cleaning & Preventive Maintenance ......................................................................................... 19
Replacing the Pump Tubing ..................................................................................................... 20
Draining the Hot Water ............................................................................................................. 21
Troubleshooting........................................................................................................................ 22
Field Calibration of the Concentrate Pumps ............................................................................. 25
Dispenser Flow Rate Calibration ............................................................................................... 26
Field Calibrating the Empty BIB Warning.................................................................................. 26
Schematic Wiring Diagram ....................................................................................................... 27
34766 112502