Filter
Top Products
www.enviromaster.com
Side Discharge Condensers
3
PRODUCT DESCRIPTION
The AmericaSeries S1C/H and S2C
condensing units are, air-cooled, vertically
arranged side discharge, high efciency
units designed specically to meet or ex-
ceed a 13 SEER rating.
The S1C 9,000-36,000 Btuh and S1H
9,000-24,000 Btuh capacity condensing unit
will provide cooling for a single evaporator,
as identied in the "S1C Specications and
Dimensions" section on pages 23-24.
The S2C 18,000 (99) - 21,000 (92) and
23,000 (22) Btuh capacity condensing units
will provide cooling for two evaporators, as
identied on page 25 in the "S2C Specica-
tions and Dimensions" section. The S1C/H
and S2C are quiet units that can be recom-
mended for both commercial and residential
applications.
Installation of the S1C/H and S2C
condensing units is simplied by a 24V
control interconnection from the evaporator
and multiple units can be lined up in close
proximity to an exterior wall. Service valves
are recessed to reduce tampering and
all 9,000-12,000 Btuh units are equipped
with a Duratec Performance Package that
includes an oversized suction accumula-
tor with surge bafes and enhanced oil
management, a factory installed solid core
lter drier and loss of charge switch. A eld
installed crankcase heater is standard on
S1H 09 &12 (Thermostatically controlled)
models, and is available as optional equip-
ment on other models.
• Compressor and fan motor contactor
• Run capacitor
• Loss of charge switch (09 - 12 only)
• Low voltage terminal connections
• Large capacity suction accumulator
(09 - 12 only)
• Solid core lter drier (09 - 12 only)
• Thermostatically controlled crankcase
heater (09 - 12 S1H’s)
• H.P.S. (High pressure switch)
- Standard on S1H’s (heat pumps)
- Standard on S1C’s 18K and above.
• Low Ambient controls
for operation
down to 32º F
standard,
factory in-
stalled
on all S1H’s (heat pumps)
• Field installed crankcase heater
for straight cool units (standard on
9,000-12,000 Btuh S1H’s Thermostati-
cally controlled)
• Straight cool hard start (standard on
all S1H’s)
• 115V (9,000-12,000 Btuh only)
• Copper/copper coils (sea coast use)
• Low Ambient controls
for operation down
to 32º F
, specify this option for S1C or
S2C systems (standard on S1H’s) that
will be operated in cooling mode at
outside temperatures below 60º F
(eld
installed kit)
•
Low Ambient
for operation down to 0º F
for S1C, S1H or S2C systems (consult
factory for availability)
INSTALLER SUPPLIED ITEMS
• Power wiring
• Low Volt wiring (18 awg minimum)
• Secure mounting pad or foundation
• Refrigerant piping (if not purchased
from EMI)
• High Volt Disconnect
• Refrigerant for charging interconnect
piping (see charge table on page 10)
ITEMS FOR CONSIDERATION
Low Ambient controls are required when
the system is asked to cool at outdoor tem-
peratures below 60º F, this may cause dam-
age to the compressor and coil, and may
Thermostatically controlled crankcase
heater – This feature energizes the crank-
case heater only when needed, removes
the heater from the electrical circuit at
conditions where it’s not required, saving
unnecessary Watts, and increasing overall
system efciency.
CONTROLS AND COMPONENTS
(Factory Installed or Supplied)
SYSTEM OPTIONS