Filter
Top Products
After a Clean Cycle
When the clean cycle is finished, the word “CLEAN”
After a clean cycle, you may notice some white ash in
will go out in the display and the oven will begin to the oven. Just wipe it up with a damp cloth. If white
cool. When the oven temperature has fallen below the
spots remain, remove them with a soap-filled steel wool
locking temperature the word “LOCK” goes out and
pad. Be sure to rinse thoroughly with a vinegar and
the door can be opened.
water mixture. These deposits are usually a
sdt
residue
that cannot be removed by the clean cycle.
If the oven is not clean after one clean cycle, the cycle
may be repeated.
How
to Delay Start of Cleaning
Delay Start is setting the oven timer to start the clean
cycle automatically at a later time than the present time
of day. NOTE: Before beginning, make sure the oven
clock shows the correct time of day.
Quick Reminder—Delay Start for Self-Clean:
1. Prepare the oven for cleaning.
2. Close and latch the oven door.
3. Press the CLEAN pad.
4. Press the INCREASE pad. If you wish to
change preset clean time of 4 hours, press the
INCREASE/DECREASE pad until desired
time appears.
5. Press the STOP TIME pad.
Time that appears is 4 hours later than the time of
day. Press the INCREASE pad until the Stop Time
you desire appears in the display. The self-clean
cycle will automatically begin 4 hours before the
Stop Time you select.
For example:
Let’s say it’s
7:00
and you want the
oven to begin self-cleaning at
9:00
after you’re finished
in the kitchen. The oven has been preset to clean for
four hours.
1. Prepare the oven for cleaning.
2. Close the oven door and slide the latch handle to the
right
as far as it will
go.
Make sure the oven
light
is
o~.
Never force the
fioor
latch handle.
Forc;ng
the
handle may damage the door lock mechanism.
n
3.
Press the CLEAN pad.
CLEAN
n
4. Press the INCREASE pad.
A
The oven is set.
~
5. Clean Time is preset for 4 hours. You can change the
Clean Time to
&ywhere
between 2 and 4 hours,
depending on how dirty the oven is. If a shorter Clean
Time is desired, press the DECREASE pad until the
desired Clean Time is displayed.
STOP
TIME
6. Press the STOP TIME pad.
“11:00”
appears on display and “STOP
TIME” flashes. The control
automatically sets Stop Time by
adding the Clean Time to the time of
day. In this example, the time of day
is
7:00
and the Clean Time is 4 hours.
Adding 4 hours to the time of day
equals
11:00.
7. Change the Stop Time from
11:00
to
1:00
by pressing
the INCREASE pad until”1
:00”
appears
in the display. The words “DELAY
CLEAN7’
will
also appear in the display.
The self-clean cycle will automatically begin at
9:00
and finish at 1:00. The word “ON” will appear on the
display at
9:00.
When the oven locks, the word “LOCK” will be
displayed and a short time later, the door latch handle
will be locked in position. It will not be possible to open
the oven door until the temperature drops below the
lock temperature.
When the clean cycle is finished, the word “CLEAN”
will go out in the display and the oven will begin to
cool. When the oven temperature has fallen below
the locking temperature the word “LOCK” goes out and
the door can be opened.
8. When the LOCK light is off, slide the latch handle to
the left as far as it will go and open the door.
Never force the latch handle. Wait until the word
“LOCK” goes out in the display. Forcing the latch
handle may damage the door
lock.
(continued next page)
23