Filter
Top Products
u
Clean the plastic surfaces, outside and inside, by
hand using lukewarm water and a little dish washing
liquid.
u
To clean the drain opening:
Remove deposits with a thin
instrument, e.g. a cotton bud.
u
Most of the equipment parts can be dismantled for
cleaning: see the respective chapter.
u
Clean the roller plates for the vegetable trays in the
dishwasher.
u
Clean the other fittings by hand using lukewarm water
and a little dish washing liquid.
After cleaning:
u
Wipe the appliance and accessories dry.
u
Connect the appliance and switch it on again.
u
Switch on SuperFrost (see 5.7.4) .
When the temperature is sufficiently cold:
u
put the food back in the appliance.
6.3 Cleaning the IceMaker*
Fig. 7
The IceMaker must be switched on.
u
Pull out the drawer and take out the ice.
u
Clean the drawer with warm water and mild dish deter-
gent.
u
With the drawer pulled out, press and hold the On/Off
button (for about 10 seconds).
w
After about 1 second the LED goes out, the IceMaker is
switched off.
w
After about 10 seconds the LED flashes for about 60
seconds.
u
Push the drawer in while the LED is flashing.
w
The ice tray of the IceMaker rotates and tilts.
u
Take out the drawer.
u
Clean the ice tray with warm water. If necessary, use a
mild dish detergent. Then rinse.
To switch the IceMaker on again:
u
Press the ON/OFF button until the LED lights up, then
push the drawer in.
w
The IceMaker starts to produce ice cubes.
If dish detergent was used:
u
Throw out the first three batches of ice cubes to get rid
of any soapy residues.
6.4 Replacing the interior light*
Light bulb data
q
max. 25 W (25 W)
q
120 V
q
Bulb fitting: E14
q
Current and voltage must agree with the details on the
rating plate.
WARNING
Danger of electric shock.
u
First, remove the plug or switch off the fuse.
CAUTION
Cutting hazard!
u
To prevent possible injury due to broken glass, use
hand protection when replacing the interior light.
u
Take hold of the light cover at
the top and bottom
Fig. 8 (1)
.
u
.Unclip light cover
Fig. 8 (2)
at
the back and unhook.
u
Replace the light bulb
Fig. 8 (3)
.
When turning it, use a little more
force to overcome the static fric-
tion of the seal. Make sure the
seal sits cleanly in the light
socket.
u
Hook the cover in again at the
back and clip in at the sides.
Fig. 8
6.5 Customer service
First check whether you can remedy the fault yourself
(see Troubleshooting). If this is not the case, please
contact a qualified service provider.
WARNING
Risk of injury from repairs by non-professionals.
u
Repairs and work on the appliance and the power
supply cable not described in the Manual (see Mainte-
nance) should only be carried out by a qualified service
provider.
u
Read the appliance
designation
Fig. 9 (1)
, service no.
Fig. 9 (2)
and serial
no.
Fig. 9 (3)
from the
rating plate. The
rating plate is
located inside the
appliance on the
left-hand side.
Fig. 9
u
Notify a qualified service provider, specifying the fault,
appliance designation
Fig. 9 (1)
, service no.
Fig. 9 (2)
and serial
Fig. 9 (3)
no.
w
This will help us to provide you with a faster and more
accurate service.
Maintenance
* Depending on model and options 13