Filter
Top Products
21. USE AND CARE
Power Pack Cleaning
Stainless steel cleaning:
Do:
• Regularly wash with clean cloth or rag soaked with warm
water and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after
cleaning. Wipe dry completely.
• You may also use a specialized household stainless steel
cleaner.
Don’t:
• Use any steel or stainless steel wool or any other scrapers
to remove stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the
power pack During construction/renovation, cover the power
pack to make sure no dust sticks to stainless steel surface.
- 12 -
Avoid when choosing a detergent:
- Any cleaners that contain bleach will attack stainless steel.
- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should
never be used close to a range.
22. OPERATION
Always turn your power pack on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few
minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.
A. D
ELAY SWITCH:
When a blower speed is selected, press this switch to activate the delay function. The corresponding blower speed switch
will flash to indicate this function is activated. The blower will continue to operate for 5 minutes and will stop automatically.
To cancel the delay function, press the delay switch once again.
B. S
TART/STOP/SPEED SELECTION SWITCHES:
Press the switch corresponding to the desired blower speed (from 1 for low speed to 4 for high speed). The chosen switch
will light. To turn off the blower, press once more on the corresponding blower speed switch; the switch light will shut off.
NOTE: When blower is off, pressing on blower speed 1 switch will cause the blower to start on high speed for a very
short lapse of time, and then resume on speed 1.
C. M
ASTER OFF/FILTER MAINTENANCE/HEAT SENTRY (TRIPLE FUNCTION SWITCH):
i. To turn off the blower(s) and the light simultaneously, press this switch once.
ii. After 25 hours of operation, this switch will light to indicate the filters and the blower wheel(s) need to be cleaned in
order to maintain efficient operation of the unit. The switch light will stay on until the function is reset by pressing this
switch for 3 seconds.
iii. The light indicator is used for the Heat Sentry function as well.
H
EAT SENTRY: The hood is equipped with a protective device that activates when excessive heat is detected inside the hood
and when it is set on speed 4. This device takes control of the blower and deactivates speed 4 for a 10-minute
period and sets it on speed 3. During the Heat Sentry activation, only speed 3 can be used; the Heat Sentry
button (C) will flash while the speed 3 button will light. The hood can also be turned OFF.
D. L
IGHT SWITCH:
This switch allows three different lighting levels according to your needs. Press once for nightlight, twice for normal or three
times to obtain full intensity. To shut off the lights without turning off the blower, press once more.
HC0023
A
BCD
Blower(s) Cleaning
Remove the filters in order to access the blower(s). Vacuum blower(s) to clean. Do not immerse in water.
Filters
The filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates more
grease — like frying foods or wok cooking.
Remove filters by pushing it towards the back of power pack and rotating filter downward. Filters are dishwasher safe. Allow
filters to dry completely before reinstalling them in the power pack.
Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filters may occur if using
phosphate detergent or as a result of local water conditions — but this will not affect filter performance. This discoloration is not
covered by the warranty.