Filter
Top Products
10
MENU SETTINGS
To access the settings menu, press the button corresponding to
MENU. Scroll through the menu by pressing the scrolling arrow
(< or >) (g. 9).
Rinsing
Use this function to deliver hot water from the spout to heat the internal
circuit and make the coee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Rinsing” is
displayed;
3. Press the button. “Conrm?” is displayed;
4. Press the button (g. 3). Hot water ows out of
the spout, heating the internal circuit and making the cof-
fee delivered hotter.
Descaling
For instructions on descaling, see page 18.
Install lter
For instructions on how to install the lter, see the section “Wa-
ter softener lter” (page 19).
Replacing the lter (if installed)
For instructions on how to replace the lter, see the section
“Replacing the lter” (page 20).
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Adjust time”
is displayed;
3. Press the button (g. 3). The hours ash on the
display;
4. Press the scrolling arrow (< or >) (g. 8) to change the
hour;
5. Press the button to conrm. The minutes ash;
6. Press the scrolling arrow (< or >) (g. 9) to change the
minutes;
7. Press the button to conrm.
The time is set: press the MENU/ESC button to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable Auto-start, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Auto-start”
is displayed;
3. Press the button. “Enable?” is displayed;
4. Press the button to conrm;
5. Press the scrolling arrow (< or >)
to choose the hour;
6. Press the button to conrm;
7. Press the scrolling arrow (< or >) (g. 9) to change the
minutes;
8. Press the button to conrm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been conrmed, activation of auto-start
is indicated by the small bell ( ) displayed alongside the
time.
To disable the function:
1. Select auto-start from the menu;
2. Press the button. “Disable?” is displayed;
3. Press the button to conrm.
The small bell ( ) is no longer displayed.
Auto-o
When this function is enabled:
- the appliance is automatically turned o completely, re-
leasing the main switch. To turn the appliance on again,
press the main switch (A20) and then the ON/stand-by
button (A23).
When this function is disabled:
- the appliance switches to stand-by; power remains on
and it consumes a minimal amount of electricity.
To turn the appliance on again, press the ON/stand-by
button (A23).
The stand-by time can be modied using “Auto-o timer” (if
“Auto-o” is enabled) or “Auto-standby timer ” (if “Auto-o” is
disabled).
To enable or disable auto-o, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Auto-
standby timer” (or Auto-o) is displayed;
3. Press the button. “Enable?” or “Disable?” is dis-
played;
4. Press the button to conrm;
5. Press the MENU/ESC button to exit the menu.
Auto-standby timer/ auto-o timer
Auto-o can be set so that the appliance goes o after 15 or 30
minutes, or 1, 2 or 3 hours.
To re-programme Auto-o, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Auto-
standby timer” (or “Auto-o”) is displayed;