DeLonghi ETAM36.365 Coffeemaker User Manual


  Open as PDF
of 22
 
11
3. Press the button;
4. Press the scrolling arrow (< or >) (g. 9) until the number
of minutes/hours of operation is displayed (15 or 30 min-
utes, or 1, 2 or 3 hours);
5. Press the button to conrm;
6. Press the MENU/ESC button to exit the menu.
Auto-o is programmed.
Energy saving
Use this function to enable or disable energy saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Energy
saving” is displayed;
3. Press the button. “Disable?” is displayed (or “En-
able?” if the function has already been disabled);
4. Press the button to disable (or enable) energy
saving mode;
5. Press the MENU/ESC button to exit the menu.
When the function is active, “Energy saving” is displayedafter a
period of inactivity.
Please note!
• Wheninenergysavingmode,afewsecondselapsebefore
the rst coee, cappuccino or milk based coee is deliv-
ered as the appliance must heat up again.
• Toprepareadrink,pressanybuttontoexitenergysav-
ing, then press the button corresponding to the drink you
want to make.
• Ifthemilkcontainerisattachedtotheappliance,theen-
ergy saving function is not active.
Setting the temperature
To modify the temperature of the water used to make the cof-
fee, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Set tem-
perature” is displayed;
3. Press the button;
4. Press the scrolling arrow (< or >) until the required tem-
perature is displayed (●=low; ●●●●=maximum);
5. Press the button to conrm;
6. Press the MENU/ESC button to exit the menu.
Setting water hardness
For instructions on setting water hardness, see page 19.
Setting the language
To modify the language of the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Set lan-
guage” is displayed;
3. Press the button;
4. Press the the scrolling arrow (< or >) until the required
language is displayed ;
5. Press the button to conrm;
6. The set language is displayed;
7. Press the MENU/ESC button to exit the menu.
Beep
This enables or disables the beep emitted by the machine each
time the buttons are pressed or an accessory is inserted/re-
moved. To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Beep” is
displayed;
3. Press the button. “Disable?” is displayed (or “En-
able?” if disabled);
4. Press the button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
Cup lighting
This function enables or disables the cup lighting. The lighting
is enabled by default.
The lighting comes on each time coee, cappuccino or milk
based coee is made and during each rinsing cycle.
To disable or re-enable this function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Cup light-
ing” is displayed;
3. Press the button. “Disable?” is displayed (or “En-
able?” if disabled);
4. Press the button to enable or disable the cup
lighting;
5. Press the MENU/ESC button to exit the menu.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as set).
To reset the default values, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the scrolling arrow (< or >) (g. 9) until “Default
values” is displayed;
3. Press the button;
4. “Conrm?” is displayed;
5. Press the button to conrm and exit.
Statistics function
This displays statistics relating to the machine.
 previous next