Filter
Top Products
6801 SERIES
MEAT SAW
Printed On Recycled Paper
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 4 of 4 F-39903 – 6801 Series Meat Saw
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
F-39903 (REV. 8/03) LITHO IN U.S.A. (H-01)
SOLUTIONS / BENEFITS
3 H.P. Motor
Durability and reliability
■ Totally enclosed
■ Flange mounted with grease-packed ball bearings
■ Water resistant
Direct Gear Drive Transmission
Performance
■ No belts to replace, slip, adjust or break
■ Helical gear reduction
■ Blade speed; 4150 fpm
Safety Features
Safety
■ Upper and lower pulleys are completely enclosed
■ Accessible blade is guarded above and below the
cutting zone
■ Pusher plate provided to eliminate handling items
too close to blade
Cleanability
Labor savings, improved sanitation
■ Total open construction and complete hose down
capabilities
■ Lower “lift-out” guide assembly has stainless steel
blade guide
■ Built-in tungsten carbide blade back-up block
assembly is removable
■ Enclosed bone dust system, with large lower scrap
pan, keeps dust where it belongs
■ No tools needed for part removal, including both
pulleys, blade cleaners and guide assemblies
■ Exclusive two-piece table and open frame design
make sink washing or high pressure hose-down a
cinch
Pivoted Automatic Tension
Productivity, ease of use
■ Entire motor, transmission and lower pulley
assembly is pivot mounted
■ Blade tension control accessible just below right
table
■ Simple adjustment allows for broad blade length
tolerance
User Friendly Controls
Ease of use
■ Single pull-to-start, push-to-stop switch
■ Heater provided with each control to prevent
moisture condensation on electrical components
Integrated Pulley Design
Durability, reliability
■ Bright tinned cast iron upper and lower blade pulleys
are easily removed
■ True-running of the blade is assured by precision
pulley balance
■ Blade retaining double flanges and center crown
give long life without loss of blade integrity
Movable Carriage Tray
Convenience, labor savings
■ 16" D x 24
1
⁄4" W
■ Stainless steel, turned down edges provide
reinforcements for rigidity
■ Stepped front edge makes movement of carriage
fast and easy
■ Stainless steel ball bearings, mounted on underside
of carriage
■ Tri-rail carriage support assures stability and easy
travel, even when operator leans heavily on carriage
■ Carriage lock is provided as standard equipment
Rugged Gauge Plate
Durability, ease of operation
■ Stainless steel plate on aluminum cast frame,
6
3
⁄4" x 16
3
⁄4"
■ Adjustment gives quick, positive regulation of cut
thickness with precision
■ Easily disengaged for adjustment
■ Exclusive design of gauge plate end permits quick
removal of cuts for stacking
Stationary Cutting Table
Convenience, heavy duty
■ Two piece, 21
1
⁄2" x 39
5
⁄8", heavy stainless steel with
turned down edges for rigidity
■ Fully supported for heavy duty use
■ Provides extensive stacking space and easy
breakdown for cleaning
SPECIFICATIONS
Motor: 3 H.P.
Electrical: Available in 230/60/1, 200-230/60/3, 460/60/3.
Also available in 220/50/3, 380-415/50/60/3, not submitted
for U L listing.
Switch: Single pull-to-start, push-to-stop switch
Standard Leg Height: 2" (Std.) 1
3
⁄4" to 2
1
⁄4"
Optional Leg Height: 4" 3
3
⁄4" to 4
1
⁄4"
Saw Blade:
5
⁄8" wide x 142" long
Capacity: Cutting clearance is 17
1
⁄2" H x 15
3
⁄4" W
Weight: Net 430 lbs. Shipping: approximately 570 lbs.
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
6801 Meat Saw Technical Manual Page 6 of 51